shithub: docs.9front.org

ref: b9b2ce4592015b0dc049661059ed2af4a9696f54
dir: /cpu-setup.md/

View raw version
# Setting up a networked 9front machine

0. First off, we'll make our life bearable by setting up a
   temporary cpu service listener. This will let us access the
   new system with `rcpu(1)` or `drawterm(1)`, instead of having
   to suffer some terrible VNC console or similar.

   Make sure the machine has network access, then run the following:

	echo 'key proto=dp9ik dom=9front user='$user' !password=BADBADDIE' >/mnt/factotum/ctl
	aux/listen1 -t 'tcp!*!rcpu' /rc/bin/service/tcp17019

1. Complete the standard installation using inst/start, then reboot
   into a newly installed system.

   The following steps assume the cwfs(4) was selected as the
   file server, and that the basic networking works.

2. Start with adding your own user to the file server, also add
   it to some standard groups:

	; con -C /srv/cwfs.cmd
	newuser kvik
	newuser sys +kvik
	newuser adm +kvik
	newuser upas +kvik

   Before proceeding, restart the machine and log in with the new
   user, then run:

	/sys/lib/newuser

   This will set up your home directory.

3. Setting up the FS listener

   This step is OPTIONAL.  If you don't plan to set up
   TCP/TLS or PXE booting it is fine to skip it for now.

   For `cwfs(4)` to start a network listener it must be told to
   to so in the command line used to start it.  This can be done
   through the `plan9.ini`.

   First we'll need to mount the `9fat` partition. If you aren't doing
   this from the console, i.e. you've done step 0., then you'll have
   to make sure you are mounting and modifying the target machine's
   `plan9.ini`, and not the one belonging to your terminal.  We can do
   this by binding correct devices and being explicit with the `9fs`
   command:

	; bind -b '#S' /dev
	; 9fs 9fat /dev/sdF0/9fat

   You may now edit `/n/9fat/plan9.ini`.

   Modify the `bootargs=` parameter as follows, or use the equivalent
   `nobootprompt=` parameter to avoid the need for manual intervention
   during the boot. The latter is highly recommended.

	nobootprompt=local!/dev/sdF0/fscache -a tcp!*!564

   This tells `cwfs(4)` to start a listener on port 564.

   By default the file server doesn't require authentication, this
   is so that local mounting can work without an auth server. However,
   with the previous step we've exposed the file server to the network
   which means anyone could mount it just by guessing an existing user.
   To prevent this we'll tell the file server to authenticate remote
   clients. This is done on the file server console by toggling the
   `noauth` command.  Make sure you get `auth enabled` message.

	; con -C /srv/cwfs.cmd
	noauth
	auth enabled

4. Setting up the CPU listener

   For CPU listener to get started at boot time it is enough to set
   the `service=` parameter in `plan9.ini`:

	service=cpu

5. Setting up hands-free booting

   In step 3. we've set up the `nobootprompt=` parameter, which makes
   sure the root file system is mounted automatically at boot.  
   In this step we'll set up hostowner credentials, the user name and
   password, so as to avoid the need for manual intervention on the
   system console.

   The auth credentials must be stored in the system NVRAM, which
   is usually a small disk partition on PC systems.  We can
   write to it with the `auth/wrkey(8)`.

   **NOTE** Make very sure to enter correct information when prompted.
   It is very common for people to mistype their password, or specify
   a wrong authentication domain, or even username, which will cause
   very hard to diagnose problems later on.  The same information will
   be asked for later when creating an auth user and configuring the
   authentication server.

   **NOTE 2** If you have followed the step 0. then it is best to
   explicitly specify the `nvram` partition that you want to write to.
   On PC some automatic process is used to find a suitable partition.
   It is very likely that this process will guess wrong.  Use the
   `nvram=` environment variable to select the correct partition:

	; nvram=/dev/sdF0/nvram auth/wrkey
	bad nvram des key
	bad authentication id
	bad authentication domain
	authid: kvik
	authdom: a-b.xyz
	secstore key: <press enter to skip>
	password: <type your password>

6. Setting up the AUTH server

   We are almost done and ready to reboot, but almost nothing set
   up above will work before an authentication server is running.

   First we'll have to make sure that the authentication server
   process starts during boot. This is done automatically by the
   CPU machine's bootup procedure if it learns that it is supposed
   to be the authentication server.  We tell it so by adding an
   entry in the system network database which associates the
   machine, the auth server, with an authentication domain that
   it will serve.

   Add the following entry on a line of its own in the file
   `/lib/ndb/local`, replacing the domain with some domain or string
   of your own:

	auth=dum authdom=a-b.xyz

   This associates the machine named `dum` with the authentication
   domain `a-b.xyz`. Remember that this was the same authdom: that we
   stored in the machine's nvram with `auth/wrkey`.

   **NOTE** this entry is independent from everything else in this
   file. Do not add it to either the `ipnet=` entry, or the `sys=`
   line.

   On next reboot the machine `dum` will figure out it's supposed
   to be an authentication server and start the services it needs
   to act as one.

   Now we can add users to the auth server. For this start a temporary
   `keyfs(4)`, then use `auth/changeuser(8)` command to add users:

	; auth/keyfs
	; auth/changeuser kvik
	Password: <same as what's in nvram>
	Confirm password: 
	assign new Inferno/POP secret? [y/n]: n
	Expiration date (YYYYMMDD or never)[never]: 
	Post id: 
	User's full name: 
	Department #: 
	User's email address: kvik@a-b.xyz
	Sponsor's email address: 
	user kvik installed for Plan 9

   Final step involves letting our new user "speak for" other users.
   This is neccessary if the hostowner of the machine
   running the auth server is someone other than `glenda`, which
   is the case here.

   Simply add the following entry to the file `/lib/ndb/auth`:

	hostid=kvik
		uid=!sys uid=!adm uid=*

7. Reboot

	fshalt -r

   After reboot the machine should bring itself up automagically and
   let you connect to it using `drawterm` or `rcpu`.