ref: 1216c06c3bdf3f3fb953ec96de99e026ef318360
dir: /sys/src/9/omap/mem.h/
/* * Memory and machine-specific definitions. Used in C and assembler. */ #define KiB 1024u /* Kibi 0x0000000000000400 */ #define MiB 1048576u /* Mebi 0x0000000000100000 */ #define GiB 1073741824u /* Gibi 000000000040000000 */ #define HOWMANY(x, y) (((x)+((y)-1))/(y)) #define ROUNDUP(x, y) (HOWMANY((x), (y))*(y)) /* ceiling */ #define ROUNDDN(x, y) (((x)/(y))*(y)) /* floor */ #define MIN(a, b) ((a) < (b)? (a): (b)) #define MAX(a, b) ((a) > (b)? (a): (b)) /* * Not sure where these macros should go. * This probably isn't right but will do for now. * The macro names are problematic too. */ /* * In B(o), 'o' is the bit offset in the register. * For multi-bit fields use F(v, o, w) where 'v' is the value * of the bit-field of width 'w' with LSb at bit offset 'o'. */ #define B(o) (1<<(o)) #define F(v, o, w) (((v) & ((1<<(w))-1))<<(o)) #define FCLR(d, o, w) ((d) & ~(((1<<(w))-1)<<(o))) #define FEXT(d, o, w) (((d)>>(o)) & ((1<<(w))-1)) #define FINS(d, o, w, v) (FCLR((d), (o), (w))|F((v), (o), (w))) #define FSET(d, o, w) ((d)|(((1<<(w))-1)<<(o))) #define FMASK(o, w) (((1<<(w))-1)<<(o)) /* * Sizes */ #define BY2PG (4*KiB) /* bytes per page */ #define PGSHIFT 12 /* log(BY2PG) */ #define PGROUND(s) ROUNDUP(s, BY2PG) #define ROUND(s, sz) (((s)+(sz-1))&~(sz-1)) #define MAXMACH 1 /* max # cpus system can run */ #define MACHSIZE BY2PG #define KSTKSIZE (16*KiB) /* was 8K */ #define STACKALIGN(sp) ((sp) & ~3) /* bug: assure with alloc */ /* * Address spaces. * KTZERO is used by kprof and dumpstack (if any). * * KZERO (0xc0000000) is mapped to physical 0x80000000 (start of dram). * u-boot claims to occupy the first 3 MB of dram, but we're willing to * step on it once we're loaded. Expect plan9.ini in the first 64K past 3MB. * * L2 PTEs are stored in 1K before Mach (11K to 12K above KZERO). * cpu0's Mach struct is at L1 - MACHSIZE(4K) to L1 (12K to 16K above KZERO). * L1 PTEs are stored from L1 to L1+32K (16K to 48K above KZERO). * KTZERO may be anywhere after that (but probably shouldn't collide with * u-boot). * This should leave over 8K from KZERO to L2 PTEs. */ #define KSEG0 0xC0000000 /* kernel segment */ /* mask to check segment; good for 512MB dram */ #define KSEGM 0xE0000000 #define KZERO KSEG0 /* kernel address space */ #define L1 (KZERO+16*KiB) /* tt ptes: 16KiB aligned */ #define CONFADDR (KZERO+0x300000) /* unparsed plan9.ini */ /* KTZERO must match loadaddr in mkfile */ #define KTZERO (KZERO+0x310000) /* kernel text start */ #define UZERO 0 /* user segment */ #define UTZERO (UZERO+BY2PG) /* user text start */ #define UTROUND(t) ROUNDUP((t), BY2PG) /* moved USTKTOP down to 512MB to keep MMIO space out of user space. */ #define USTKTOP 0x20000000 /* user segment end +1 */ #define USTKSIZE (8*1024*1024) /* user stack size */ /* address at which to copy and execute rebootcode */ #define REBOOTADDR KADDR(0x100) /* * Legacy... */ #define BLOCKALIGN 32 /* only used in allocb.c */ #define KSTACK KSTKSIZE /* * Sizes */ #define BI2BY 8 /* bits per byte */ #define BY2SE 4 #define BY2WD 4 #define BY2V 8 /* only used in xalloc.c */ #define CACHELINESZ 64 /* bytes per cache line */ #define PTEMAPMEM (1024*1024) #define PTEPERTAB (PTEMAPMEM/BY2PG) #define SEGMAPSIZE 1984 /* magic 16*124 */ #define SSEGMAPSIZE 16 /* magic */ #define PPN(x) ((x)&~(BY2PG-1)) /* pure page number? */ /* * With a little work these move to port. */ #define PTEVALID (1<<0) #define PTERONLY 0 #define PTEWRITE (1<<1) #define PTEUNCACHED (1<<2) #define PTEKERNEL (1<<3) /* * Physical machine information from here on. */ /* gpmc-controlled address space 0—1G */ #define PHYSNAND 1 /* cs0 is onenand flash */ #define PHYSETHER 0x2c000000 #define PHYSIO 0x48000000 /* L4 ctl */ #define PHYSSCM 0x48002000 /* system control module */ /* core control pad cfg 0x48002030—0x480021e4, */ /* core control d2d pad cfg 0x480021e4—0x48002264 */ #define PHYSSCMPCONF 0x48002270 /* general device config */ #define PHYSOMAPSTS 0x4800244c /* standalone short: has l2 size */ /* core control pad cfg (2) 0x480025d8—0x480025fc */ #define PHYSSWBOOTCFG 0x48002910 /* sw booting config */ /* wakeup control pad cfg 0x48002a00—0x48002a54 */ #define PHYSSCMMPU 0x48004900 /* actually CPU */ #define PHYSSCMCORE 0x48004a00 #define PHYSSCMWKUP 0x48004c00 #define PHYSSCMPLL 0x48004d00 /* clock ctl for dpll[3-5] */ #define PHYSSCMDSS 0x48004e00 #define PHYSSCMPER 0x48005000 #define PHYSSCMUSB 0x48005400 #define PHYSL4CORE 0x48040100 /* l4 ap */ #define PHYSDSS 0x48050000 /* start of dss registers */ #define PHYSDISPC 0x48050400 #define PHYSGFX 0x48050480 /* part of dispc */ #define PHYSSDMA 0x48056000 /* system dma */ #define PHYSDMA 0x48060000 #define PHYSUSBTLL 0x48062000 /* usb: transceiver-less link */ #define PHYSUHH 0x48064000 /* usb: `high-speed usb host' ctlr or subsys */ #define PHYSOHCI 0x48064400 /* usb 1.0: slow */ #define PHYSEHCI 0x48064800 /* usb 2.0: medium */ #define PHYSUART0 0x4806a000 #define PHYSUART1 0x4806c000 #define PHYSMMCHS1 0x4809c000 /* mmc/sdio */ #define PHYSUSBOTG 0x480ab000 /* on-the-go usb */ #define PHYSMMCHS3 0x480ad000 #define PHYSMMCHS2 0x480b4000 #define PHYSINTC 0x48200000 /* interrupt controller */ #define PHYSPRMIVA2 0x48206000 /* prm iva2 regs */ /* 48306d40 sys_clkin_sel */ #define PHYSPRMGLBL 0x48307200 /* prm global regs */ #define PHYSPRMWKUSB 0x48307400 #define PHYSCNTRL 0x4830a200 /* SoC id, etc. */ #define PHYSWDT1 0x4830c000 /* wdt1, not on GP omaps */ #define PHYSGPIO1 0x48310000 /* contains dss gpio */ #define PHYSWDOG 0x48314000 /* watchdog timer, wdt2 */ #define PHYSWDT2 0x48314000 /* watchdog timer, wdt2 */ #define PHYSTIMER1 0x48318000 #define PHYSL4WKUP 0x48328100 /* l4 wkup */ #define PHYSL4PER 0x49000100 /* l4 per */ #define PHYSCONS 0x49020000 /* uart console (third one) */ #define PHYSWDT3 0x49030000 /* wdt3 */ #define PHYSTIMER2 0x49032000 #define PHYSTIMER3 0x49034000 #define PHYSGPIO5 0x49056000 #define PHYSGPIO6 0x49058000 /* contains igep ether gpio */ #define PHYSIOEND 0x49100000 /* end of PHYSIO identity map */ #define PHYSL4EMU 0x54006100 /* l4 emu */ #define PHYSL4PROT 0x54728000 /* l4 protection regs */ #define PHYSL3 0x68000000 /* l3 interconnect control */ #define PHYSL3GPMCCFG 0x68002000 /* l3 gpmc target port agent cfg */ #define PHYSL3USB 0x68004000 /* l3 regs for usb */ #define PHYSL3USBOTG 0x68004400 /* l3 regs for usb otg */ /* (target port) protection registers */ #define PHYSL3PMRT 0x68010000 /* l3 PM register target prot. */ #define PHYSL3GPMCPM 0x68012400 /* l3 gpmc target port protection */ #define PHYSL3OCTRAM 0x68012800 /* l3 ocm ram */ #define PHYSL3OCTROM 0x68012c00 /* l3 ocm rom */ #define PHYSL3MAD2D 0x68013000 /* l3 die-to-die */ #define PHYSL3IVA 0x68014000 /* l3 die-to-die */ #define PHYSSMS 0x6c000000 /* cfg regs: sms addr space 2 */ #define PHYSDRC 0x6d000000 /* sdram ctlr, addr space 3 */ #define PHYSGPMC 0x6e000000 /* flash, non-dram memory ctlr */ #define PHYSDRAM 0x80000000 #define VIRTNAND 0x20000000 /* fixed by u-boot */ #define VIRTIO PHYSIO