ref: 53f2b41ec64895a1d8bcebeeb7824c59e854eb13
dir: /sys/src/9/imx8/usdhc.c/
#include "u.h"
#include "../port/lib.h"
#include "../port/error.h"
#include "mem.h"
#include "dat.h"
#include "fns.h"
#include "io.h"
#include "../port/sd.h"
enum {
Initfreq = 400000, /* initialisation frequency for MMC */
SDfreq = 25*Mhz, /* standard SD frequency */
SDfreqhs = 50*Mhz, /* highspeed frequency */
DTO = 14, /* data timeout exponent (guesswork) */
GoIdle = 0, /* mmc/sdio go idle state */
MMCSelect = 7, /* mmc/sd card select command */
Setbuswidth = 6, /* mmc/sd set bus width command */
Switchfunc = 6, /* mmc/sd switch function command */
Voltageswitch = 11, /* md/sdio switch to 1.8V */
IORWdirect = 52, /* sdio read/write direct command */
IORWextended = 53, /* sdio read/write extended command */
Appcmd = 55, /* mmc/sd application command prefix */
};
enum {
/* Controller registers */
SDMAaddr = 0x00>>2,
Blksizecnt = 0x04>>2,
Arg1 = 0x08>>2,
Cmdtm = 0x0c>>2,
Resp0 = 0x10>>2,
Resp1 = 0x14>>2,
Resp2 = 0x18>>2,
Resp3 = 0x1c>>2,
Data = 0x20>>2,
Status = 0x24>>2,
Control0 = 0x28>>2,
Control1 = 0x2c>>2,
Interrupt = 0x30>>2,
Irptmask = 0x34>>2,
Irpten = 0x38>>2,
Control2 = 0x3c>>2,
Capability = 0x40>>2,
Mixctrl = 0x48>>2,
Forceirpt = 0x50>>2,
Dmadesc = 0x58>>2,
Vendorspec = 0xC0>>2,
/* Vendorspec */
ClkEn = 1<<14,
PerEn = 1<<13,
HclkEn = 1<<12,
IpgEn = 1<<11,
Vsel = 1<<1,
/* Control0 (PROT_CTRL) */
Dmaselect = 3<<8,
DmaSDMA = 0<<8,
DmaADMA1 = 1<<8,
DmaADMA2 = 2<<8,
EMODE = 3<<4,
BE = 0<<4,
HBE = 1<<4,
LE = 2<<4,
DwidthMask = 3<<1,
Dwidth8 = 2<<1,
Dwidth4 = 1<<1,
Dwidth1 = 0<<1,
LED = 1<<0,
/* Control1 (SYS_CTRL) */
Srstdata = 1<<26, /* reset data circuit */
Srstcmd = 1<<25, /* reset command circuit */
Srsthc = 1<<24, /* reset complete host controller */
Datatoshift = 16, /* data timeout unit exponent */
Datatomask = 0xF0000,
SDCLKFSshift = 8,
DVSshift = 4,
/* Cmdtm */
Indexshift = 24,
Suspend = 1<<22,
Resume = 2<<22,
Abort = 3<<22,
Isdata = 1<<21,
Ixchken = 1<<20,
Crcchken = 1<<19,
Respmask = 3<<16,
Respnone = 0<<16,
Resp136 = 1<<16,
Resp48 = 2<<16,
Resp48busy = 3<<16,
/* Mixctrl */
Autocmd23 = 1<<7,
Multiblock = 1<<5,
Host2card = 0<<4,
Card2host = 1<<4,
DdrEn = 1<<3,
Autocmd12 = 1<<2,
Blkcnten = 1<<1,
Dmaen = 1<<0,
MixCmdMask = 0xFF ^ DdrEn,
/* Interrupt */
Admaerr = 1<<28,
Acmderr = 1<<24,
Denderr = 1<<22,
Dcrcerr = 1<<21,
Dtoerr = 1<<20,
Cbaderr = 1<<19,
Cenderr = 1<<18,
Ccrcerr = 1<<17,
Ctoerr = 1<<16,
Err = Admaerr|Acmderr|Denderr|Dcrcerr|Dtoerr|Cbaderr|Cenderr|Ccrcerr|Ctoerr,
Cardintr = 1<<8,
Cardinsert = 1<<6,
Readrdy = 1<<5,
Writerdy = 1<<4,
Dmaintr = 1<<3,
Datadone = 1<<1,
Cmddone = 1<<0,
/* Status */
Bufread = 1<<11,
Bufwrite = 1<<10,
Readtrans = 1<<9,
Writetrans = 1<<8,
Clkstable = 1<<3,
Datactive = 1<<2,
Datinhibit = 1<<1,
Cmdinhibit = 1<<0,
};
static int cmdinfo[64] = {
[0] Ixchken,
[2] Resp136,
[3] Resp48 | Ixchken | Crcchken,
[5] Resp48,
[6] Resp48 | Ixchken | Crcchken,
[7] Resp48 | Ixchken | Crcchken,
[8] Resp48 | Ixchken | Crcchken,
[9] Resp136,
[11] Resp48 | Ixchken | Crcchken,
[13] Resp48 | Ixchken | Crcchken,
[16] Resp48,
[17] Resp48 | Isdata | Card2host | Ixchken | Crcchken,
[18] Resp48 | Isdata | Card2host | Multiblock | Blkcnten | Ixchken | Crcchken | Autocmd12,
[24] Resp48 | Isdata | Host2card | Ixchken | Crcchken,
[25] Resp48 | Isdata | Host2card | Multiblock | Blkcnten | Ixchken | Crcchken | Autocmd12,
[41] Resp48,
[52] Resp48 | Ixchken | Crcchken,
[53] Resp48 | Ixchken | Crcchken | Isdata,
[55] Resp48 | Ixchken | Crcchken,
};
typedef struct Adma Adma;
typedef struct Ctlr Ctlr;
/*
* ADMA2 descriptor
* See SD Host Controller Simplified Specification Version 2.00
*/
struct Adma {
u32int desc;
u32int addr;
};
enum {
/* desc fields */
Valid = 1<<0,
End = 1<<1,
Int = 1<<2,
Nop = 0<<4,
Tran = 2<<4,
Link = 3<<4,
OLength = 16,
/* maximum value for Length field */
Maxdma = 1<<12,
};
struct Ctlr {
Rendez r;
int fastclock;
uint extclk;
int appcmd;
Adma *dma;
};
static Ctlr usdhc;
static void usdhcinterrupt(Ureg*, void*);
static u32int *regs = (u32int*)(VIRTIO+0xB50000); /* USDHC2 */
#define RR(reg) (regs[reg])
static void
WR(int reg, u32int val)
{
if(0)print("WR %2.2ux %ux\n", reg<<2, val);
coherence();
regs[reg] = val;
}
static Adma*
dmaalloc(void *addr, int len)
{
int n;
uintptr a;
Adma *adma, *p;
a = PADDR(addr);
n = (len + Maxdma-1) / Maxdma;
adma = sdmalloc(n * sizeof(Adma));
for(p = adma; len > 0; p++){
if(n == 1)
p->desc = len<<OLength | End | Int | Valid | Tran;
else
p->desc = Maxdma<<OLength | Valid | Tran;
p->addr = a;
a += Maxdma;
len -= Maxdma;
n--;
}
cachedwbse(adma, (char*)p - (char*)adma);
return adma;
}
static void
usdhcclk(uint freq)
{
uint pre_div = 1, post_div = 1, clk = usdhc.extclk;
while(clk / (pre_div * 16) > freq && pre_div < 256)
pre_div <<= 1;
while(clk / (pre_div * post_div) > freq && post_div < 16)
post_div++;
WR(Vendorspec, RR(Vendorspec) & ~ClkEn);
WR(Control1, (pre_div>>1)<<SDCLKFSshift | (post_div-1)<<DVSshift | DTO<<Datatoshift);
delay(10);
WR(Vendorspec, RR(Vendorspec) | ClkEn | PerEn);
while((RR(Status) & Clkstable) == 0)
;
}
static int
datadone(void*)
{
return RR(Interrupt) & (Datadone|Err);
}
static int
usdhcinit(void)
{
iomuxpad("pad_sd2_clk", "usdhc2_clk", "~LVTTL ~HYS ~PUE ~ODE SLOW 75_OHM");
iomuxpad("pad_sd2_cmd", "usdhc2_cmd", "~LVTTL HYS PUE ~ODE SLOW 75_OHM");
iomuxpad("pad_sd2_data0", "usdhc2_data0", "~LVTTL HYS PUE ~ODE SLOW 75_OHM");
iomuxpad("pad_sd2_data1", "usdhc2_data1", "~LVTTL HYS PUE ~ODE SLOW 75_OHM");
iomuxpad("pad_sd2_data2", "usdhc2_data2", "~LVTTL HYS PUE ~ODE SLOW 75_OHM");
iomuxpad("pad_sd2_data3", "usdhc2_data3", "~LVTTL HYS PUE ~ODE SLOW 75_OHM");
setclkgate("usdhc2.ipg_clk", 0);
setclkgate("usdhc2.ipg_clk_perclk", 0);
setclkrate("usdhc2.ipg_clk_perclk", "system_pll1_clk", 200*Mhz);
setclkgate("usdhc2.ipg_clk_perclk", 1);
setclkgate("usdhc2.ipg_clk", 1);
usdhc.extclk = getclkrate("usdhc2.ipg_clk_perclk");
if(usdhc.extclk <= 0){
print("usdhc: usdhc2.ipg_clk_perclk not enabled\n");
return -1;
}
if(0)print("usdhc control %8.8ux %8.8ux %8.8ux\n",
RR(Control0), RR(Control1), RR(Control2));
WR(Control1, Srsthc);
delay(10);
while(RR(Control1) & Srsthc)
;
WR(Control1, Srstdata);
delay(10);
WR(Control1, 0);
return 0;
}
static int
usdhcinquiry(char *inquiry, int inqlen)
{
return snprint(inquiry, inqlen, "USDHC Host Controller");
}
static void
usdhcenable(void)
{
WR(Control0, 0);
delay(1);
WR(Vendorspec, RR(Vendorspec) & ~Vsel);
WR(Control0, LE | Dwidth1 | DmaADMA2);
WR(Control1, 0);
delay(1);
WR(Vendorspec, RR(Vendorspec) | HclkEn | IpgEn);
usdhcclk(Initfreq);
WR(Irpten, 0);
WR(Irptmask, ~(Cardintr|Dmaintr));
WR(Interrupt, ~0);
intrenable(IRQusdhc2, usdhcinterrupt, nil, BUSUNKNOWN, "usdhc2");
}
static int
usdhccmd(u32int cmd, u32int arg, u32int *resp)
{
u32int c;
int i;
ulong now;
/* using Autocmd12 */
if(cmd == 12)
return 0;
assert(cmd < nelem(cmdinfo) && cmdinfo[cmd] != 0);
c = (cmd << Indexshift) | cmdinfo[cmd];
/*
* CMD6 may be Setbuswidth or Switchfunc depending on Appcmd prefix
*/
if(cmd == Switchfunc && !usdhc.appcmd)
c |= Isdata|Card2host;
if(c & Isdata)
c |= Dmaen;
if(cmd == IORWextended){
if(arg & (1<<31))
c |= Host2card;
else
c |= Card2host;
if((RR(Blksizecnt)&0xFFFF0000) != 0x10000)
c |= Multiblock | Blkcnten;
}
/*
* GoIdle indicates new card insertion: reset bus width & speed
*/
if(cmd == GoIdle){
WR(Control0, (RR(Control0) & ~DwidthMask) | Dwidth1);
usdhcclk(Initfreq);
}
if(RR(Status) & Cmdinhibit){
print("usdhccmd: need to reset Cmdinhibit intr %ux stat %ux\n",
RR(Interrupt), RR(Status));
WR(Control1, RR(Control1) | Srstcmd);
while(RR(Control1) & Srstcmd)
;
while(RR(Status) & Cmdinhibit)
;
}
if((RR(Status) & Datinhibit) &&
((c & Isdata) || (c & Respmask) == Resp48busy)){
print("usdhccmd: need to reset Datinhibit intr %ux stat %ux\n",
RR(Interrupt), RR(Status));
WR(Control1, RR(Control1) | Srstdata);
while(RR(Control1) & Srstdata)
;
while(RR(Status) & Datinhibit)
;
}
while(RR(Status) & Datactive)
;
WR(Arg1, arg);
if((i = (RR(Interrupt) & ~Cardintr)) != 0){
if(i != Cardinsert)
print("usdhc: before command, intr was %ux\n", i);
WR(Interrupt, i);
}
WR(Mixctrl, (RR(Mixctrl) & ~MixCmdMask) | (c & MixCmdMask));
WR(Cmdtm, c & ~0xFFFF);
now = MACHP(0)->ticks;
while(((i=RR(Interrupt))&(Cmddone|Err)) == 0)
if(MACHP(0)->ticks - now > HZ)
break;
if((i&(Cmddone|Err)) != Cmddone){
if((i&~(Err|Cardintr)) != Ctoerr)
print("usdhc: cmd %ux arg %ux error intr %ux stat %ux\n", c, arg, i, RR(Status));
WR(Interrupt, i);
if(RR(Status)&Cmdinhibit){
WR(Control1, RR(Control1)|Srstcmd);
while(RR(Control1)&Srstcmd)
;
}
error(Eio);
}
WR(Interrupt, i & ~(Datadone|Readrdy|Writerdy));
switch(c & Respmask){
case Resp136:
resp[0] = RR(Resp0)<<8;
resp[1] = RR(Resp0)>>24 | RR(Resp1)<<8;
resp[2] = RR(Resp1)>>24 | RR(Resp2)<<8;
resp[3] = RR(Resp2)>>24 | RR(Resp3)<<8;
break;
case Resp48:
case Resp48busy:
resp[0] = RR(Resp0);
break;
case Respnone:
resp[0] = 0;
break;
}
if((c & Respmask) == Resp48busy){
WR(Irpten, RR(Irpten)|Datadone|Err);
tsleep(&usdhc.r, datadone, 0, 1000);
i = RR(Interrupt);
if((i & Datadone) == 0)
print("usdhcio: no Datadone in %x after CMD%d\n", i, cmd);
if(i & Err)
print("usdhcio: CMD%d error interrupt %ux\n",
cmd, RR(Interrupt));
if(i != 0) WR(Interrupt, i);
}
/*
* Once card is selected, use faster clock
*/
if(cmd == MMCSelect){
usdhcclk(SDfreq);
usdhc.fastclock = 1;
}
if(cmd == Setbuswidth){
if(usdhc.appcmd){
/*
* If card bus width changes, change host bus width
*/
switch(arg){
case 0:
WR(Control0, (RR(Control0) & ~DwidthMask) | Dwidth1);
break;
case 2:
WR(Control0, (RR(Control0) & ~DwidthMask) | Dwidth4);
break;
}
} else {
/*
* If card switched into high speed mode, increase clock speed
*/
if((arg&0x8000000F) == 0x80000001){
delay(1);
usdhcclk(SDfreqhs);
delay(1);
}
}
}else if(cmd == IORWdirect && (arg & ~0xFF) == (1<<31|0<<28|7<<9)){
switch(arg & 0x3){
case 0:
WR(Control0, (RR(Control0) & ~DwidthMask) | Dwidth1);
break;
case 2:
WR(Control0, (RR(Control0) & ~DwidthMask) | Dwidth4);
break;
}
}
usdhc.appcmd = (cmd == Appcmd);
return 0;
}
static void
usdhciosetup(int write, void *buf, int bsize, int bcount)
{
int len = bsize * bcount;
assert(((uintptr)buf&3) == 0);
assert((len&3) == 0);
assert(bsize <= 2048);
WR(Blksizecnt, bcount<<16 | bsize);
if(usdhc.dma)
sdfree(usdhc.dma);
usdhc.dma = dmaalloc(buf, len);
if(write)
cachedwbse(buf, len);
else
cachedwbinvse(buf, len);
WR(Dmadesc, PADDR(usdhc.dma));
}
static void
usdhcio(int write, uchar *buf, int len)
{
u32int i;
WR(Irpten, RR(Irpten) | Datadone|Err);
tsleep(&usdhc.r, datadone, 0, 3000);
WR(Irpten, RR(Irpten) & ~(Datadone|Err));
i = RR(Interrupt);
if((i & (Datadone|Err)) != Datadone){
print("sdhc: %s error intr %ux stat %ux\n",
write? "write" : "read", i, RR(Status));
WR(Interrupt, i);
error(Eio);
}
WR(Interrupt, i);
if(!write)
cachedinvse(buf, len);
}
static void
usdhcinterrupt(Ureg*, void*)
{
u32int i;
i = RR(Interrupt);
if(i&(Datadone|Err))
wakeup(&usdhc.r);
WR(Irpten, RR(Irpten) & ~i);
}
SDio sdio = {
"usdhc",
usdhcinit,
usdhcenable,
usdhcinquiry,
usdhccmd,
usdhciosetup,
usdhcio,
.highspeed = 1,
.nomultiwrite = 1,
};