ref: 01af5a89b3e1ac5c45472ef8ade9c15ffbd19925
dir: /demos/stm32f429_disco/stm/stm32f4_spl/src/stm32f4xx_hal_cryp.c/
/**
******************************************************************************
* @file stm32f4xx_hal_cryp.c
* @author MCD Application Team
* @version V1.0.0
* @date 18-February-2014
* @brief CRYP HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the Cryptography (CRYP) peripheral:
* + Initialization and de-initialization functions
* + AES processing functions
* + DES processing functions
* + TDES processing functions
* + DMA callback functions
* + CRYP IRQ handler management
* + Peripheral State functions
*
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
The CRYP HAL driver can be used as follows:
(#)Initialize the CRYP low level resources by implementing the HAL_CRYP_MspInit():
(##) Enable the CRYP interface clock using __CRYP_CLK_ENABLE()
(##) In case of using interrupts (e.g. HAL_CRYP_AESECB_Encrypt_IT())
(+++) Configure the CRYP interrupt priority using HAL_NVIC_SetPriority()
(+++) Enable the CRYP IRQ handler using HAL_NVIC_EnableIRQ()
(+++) In CRYP IRQ handler, call HAL_CRYP_IRQHandler()
(##) In case of using DMA to control data transfer (e.g. HAL_CRYP_AESECB_Encrypt_DMA())
(++) Enable the DMAx interface clock using
(+++) __DMAx_CLK_ENABLE()
(++) Configure and enable two DMA streams one for managing data transfer from
memory to peripheral (input stream) and another stream for managing data
transfer from peripheral to memory (output stream)
(++) Associate the initilalized DMA handle to the CRYP DMA handle
using __HAL_LINKDMA()
(++) Configure the priority and enable the NVIC for the transfer complete
interrupt on the two DMA Streams. The output stream should have higher
priority than the input stream.
(+++) HAL_NVIC_SetPriority()
(+++) HAL_NVIC_EnableIRQ()
(#)Initialize the CRYP HAL using HAL_CRYP_Init(). This function configures mainly:
(##) The data type: 1-bit, 8-bit, 16-bit and 32-bit
(##) The key size: 128, 192 and 256. This parameter is relevant only for AES
(##) The encryption/decryption key. It's size depends on the algorithm
used for encryption/decryption
(##) The initialization vector (counter). It is not used ECB mode.
(#)Three processing (encryption/decryption) functions are available:
(##) Polling mode: encryption and decryption APIs are blocking functions
i.e. they process the data and wait till the processing is finished
e.g. HAL_CRYP_AESCBC_Encrypt()
(##) Interrupt mode: encryption and decryption APIs are not blocking functions
i.e. they process the data under interrupt
e.g. HAL_CRYP_AESCBC_Encrypt_IT()
(##) DMA mode: encryption and decryption APIs are not blocking functions
i.e. the data transfer is ensured by DMA
e.g. HAL_CRYP_AESCBC_Encrypt_DMA()
(#)When the processing function is called at first time after HAL_CRYP_Init()
the CRYP peripheral is initialized and processes the buffer in input.
At second call, the processing function performs an append of the already
processed buffer.
When a new data block is to be processed, call HAL_CRYP_Init() then the
processing function.
(#)Call HAL_CRYP_DeInit() to deinitialize the CRYP peripheral.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @defgroup CRYP
* @brief CRYP HAL module driver.
* @{
*/
#ifdef HAL_CRYP_MODULE_ENABLED
#if defined(STM32F415xx) || defined(STM32F417xx) || defined(STM32F437xx) || defined(STM32F439xx)
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize);
static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize);
static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout);
static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout);
static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma);
static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma);
static void CRYP_DMAError(DMA_HandleTypeDef *hdma);
static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr);
static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);
static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);
static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);
static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction);
/* Private functions ---------------------------------------------------------*/
/** @defgroup CRYP_Private_Functions
* @{
*/
/** @defgroup CRYP_Group1 Initialization and de-initialization functions
* @brief Initialization and Configuration functions.
*
@verbatim
==============================================================================
##### Initialization and de-initialization functions #####
==============================================================================
[..] This section provides functions allowing to:
(+) Initialize the CRYP according to the specified parameters
in the CRYP_InitTypeDef and creates the associated handle
(+) DeInitialize the CRYP peripheral
(+) Initialize the CRYP MSP
(+) DeInitialize CRYP MSP
@endverbatim
* @{
*/
/**
* @brief Initializes the CRYP according to the specified
* parameters in the CRYP_InitTypeDef and creates the associated handle.
* @param hcryp: CRYP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp)
{
/* Check the CRYP handle allocation */
if(hcryp == NULL)
{
return HAL_ERROR;
}
/* Check the parameters */
assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize));
assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType));
if(hcryp->State == HAL_CRYP_STATE_RESET)
{
/* Init the low level hardware */
HAL_CRYP_MspInit(hcryp);
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set the key size and data type*/
CRYP->CR = (uint32_t) (hcryp->Init.KeySize | hcryp->Init.DataType);
/* Reset CrypInCount and CrypOutCount */
hcryp->CrypInCount = 0;
hcryp->CrypOutCount = 0;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Set the default CRYP phase */
hcryp->Phase = HAL_CRYP_PHASE_READY;
/* Return function status */
return HAL_OK;
}
/**
* @brief DeInitializes the CRYP peripheral.
* @param hcryp: CRYP handle
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp)
{
/* Check the CRYP handle allocation */
if(hcryp == NULL)
{
return HAL_ERROR;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set the default CRYP phase */
hcryp->Phase = HAL_CRYP_PHASE_READY;
/* Reset CrypInCount and CrypOutCount */
hcryp->CrypInCount = 0;
hcryp->CrypOutCount = 0;
/* Disable the CRYP Peripheral Clock */
__HAL_CRYP_DISABLE();
/* DeInit the low level hardware: CLOCK, NVIC.*/
HAL_CRYP_MspDeInit(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_RESET;
/* Release Lock */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP MSP.
* @param hcryp: CRYP handle
* @retval None
*/
__weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_CRYP_MspInit could be implemented in the user file
*/
}
/**
* @brief DeInitializes CRYP MSP.
* @param hcryp: CRYP handle
* @retval None
*/
__weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_CRYP_MspDeInit could be implemented in the user file
*/
}
/**
* @}
*/
/** @defgroup CRYP_Group2 AES processing functions
* @brief processing functions.
*
@verbatim
==============================================================================
##### AES processing functions #####
==============================================================================
[..] This section provides functions allowing to:
(+) Encrypt plaintext using AES-128/192/256 using chaining modes
(+) Decrypt cyphertext using AES-128/192/256 using chaining modes
[..] Three processing functions are available:
(+) Polling mode
(+) Interrupt mode
(+) DMA mode
@endverbatim
* @{
*/
/**
* @brief Initializes the CRYP peripheral in AES ECB encryption mode
* then encrypt pPlainData. The cypher data are available in pCypherData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CBC encryption mode
* then encrypt pPlainData. The cypher data are available in pCypherData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CTR encryption mode
* then encrypt pPlainData. The cypher data are available in pCypherData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES ECB decryption mode
* then decrypted pCypherData. The cypher data are available in pPlainData
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pPlainData: Pointer to the plaintext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)
{
uint32_t timeout = 0;
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get timeout */
timeout = HAL_GetTick() + Timeout;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
}
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES ECB decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES ECB decryption mode
* then decrypted pCypherData. The cypher data are available in pPlainData
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pPlainData: Pointer to the plaintext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)
{
uint32_t timeout = 0;
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get Timeout */
timeout = HAL_GetTick() + Timeout;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
}
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES CBC decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CTR decryption mode
* then decrypted pCypherData. The cypher data are available in pPlainData
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pPlainData: Pointer to the plaintext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES CTR mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES ECB encryption mode using Interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Locked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using Interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES CBC mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Locked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CTR encryption mode using Interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES CTR mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES ECB decryption mode using Interrupt.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t timeout = 0;
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get timeout */
timeout = HAL_GetTick() + 1;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES ECB decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CBC decryption mode using IT.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t timeout = 0;
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Get the buffer addresses and sizes */
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get timeout */
timeout = HAL_GetTick() + 1;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES CBC decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES CTR decryption mode using Interrupt.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Get the buffer addresses and sizes */
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES CTR mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 16;
hcryp->CrypInCount -= 16;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 16;
hcryp->CrypOutCount -= 16;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in AES ECB encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in AES CTR encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16.
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in AES ECB decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t timeout = 0;
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get timeout */
timeout = HAL_GetTick() + 1;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES ECB decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16 bytes
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t timeout = 0;
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES Key mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Get timeout */
timeout = HAL_GetTick() + 1;
while(HAL_IS_BIT_SET(CRYP->SR, CRYP_FLAG_BUSY))
{
/* Check for the Timeout */
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
/* Reset the ALGOMODE bits*/
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE);
/* Set the CRYP peripheral in AES CBC decryption mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in AES CTR decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 16
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize);
/* Set the CRYP peripheral in AES CTR mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @}
*/
/** @defgroup CRYP_Group3 DES processing functions
* @brief processing functions.
*
@verbatim
==============================================================================
##### DES processing functions #####
==============================================================================
[..] This section provides functions allowing to:
(+) Encrypt plaintext using DES using ECB or CBC chaining modes
(+) Decrypt cyphertext using using ECB or CBC chaining modes
[..] Three processing functions are available:
(+) polling mode
(+) interrupt mode
(+) DMA mode
@endverbatim
* @{
*/
/**
* @brief Initializes the CRYP peripheral in DES ECB encryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB encryption mode */
CRYP_SetDESECBMode(hcryp, 0);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB decryption mode */
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES CBC encryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC encryption mode */
CRYP_SetDESCBCMode(hcryp, 0);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC decryption mode */
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB encryption mode using IT.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB encryption mode */
CRYP_SetDESECBMode(hcryp, 0);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
/* Disable IT */
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES CBC encryption mode using interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC encryption mode */
CRYP_SetDESCBCMode(hcryp, 0);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
/* Disable IT */
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using IT.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB decryption mode */
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
/* Disable IT */
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC decryption mode */
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
/* Disable IT */
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in DES ECB encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB encryption mode */
CRYP_SetDESECBMode(hcryp, 0);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in DES CBC encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC encryption mode */
CRYP_SetDESCBCMode(hcryp, 0);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES ECB decryption mode */
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in DES CBC decryption mode */
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @}
*/
/** @defgroup CRYP_Group4 TDES processing functions
* @brief processing functions.
*
@verbatim
==============================================================================
##### TDES processing functions #####
==============================================================================
[..] This section provides functions allowing to:
(+) Encrypt plaintext using TDES using ECB or CBC chaining modes
(+) Decrypt cyphertext using TDES using ECB or CBC chaining modes
[..] Three processing functions are available:
(+) polling mode
(+) interrupt mode
(+) DMA mode
@endverbatim
* @{
*/
/**
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode
* then encrypt pPlainData. The cypher data are available in pCypherData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB encryption mode */
CRYP_SetTDESECBMode(hcryp, 0);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode
* then decrypted pCypherData. The cypher data are available in pPlainData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB decryption mode */
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Cypher Data and Get Plain Data */
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode
* then encrypt pPlainData. The cypher data are available in pCypherData
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC encryption mode */
CRYP_SetTDESCBCMode(hcryp, 0);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Plain Data and Get Cypher Data */
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode
* then decrypted pCypherData. The cypher data are available in pPlainData
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pPlainData: Pointer to the plaintext buffer
* @param Timeout: Specify Timeout value
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout)
{
/* Process Locked */
__HAL_LOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC decryption mode */
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Write Cypher Data and Get Plain Data */
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK)
{
return HAL_TIMEOUT;
}
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode using interrupt.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB encryption mode */
CRYP_SetTDESECBMode(hcryp, 0);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
/* Disable IT */
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call the Output data transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pPlainData;
hcryp->pCrypOutBuffPtr = pCypherData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC encryption mode */
CRYP_SetTDESCBCMode(hcryp, 0);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB decryption mode */
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if(hcryp->State == HAL_CRYP_STATE_READY)
{
/* Process Locked */
__HAL_LOCK(hcryp);
hcryp->CrypInCount = Size;
hcryp->pCrypInBuffPtr = pCypherData;
hcryp->pCrypOutBuffPtr = pPlainData;
hcryp->CrypOutCount = Size;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC decryption mode */
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Enable Interrupts */
__HAL_CRYP_ENABLE_IT(CRYP_IT_INI | CRYP_IT_OUTI);
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Return function status */
return HAL_OK;
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_INI))
{
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr;
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
hcryp->pCrypInBuffPtr += 8;
hcryp->CrypInCount -= 8;
if(hcryp->CrypInCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_INI);
/* Call the Input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
}
else if(__HAL_CRYP_GET_IT(CRYP_IT_OUTI))
{
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr;
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
hcryp->pCrypOutBuffPtr += 8;
hcryp->CrypOutCount -= 8;
if(hcryp->CrypOutCount == 0)
{
__HAL_CRYP_DISABLE_IT(CRYP_IT_OUTI);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call Input transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB encryption mode */
CRYP_SetTDESECBMode(hcryp, 0);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pPlainData;
outputaddr = (uint32_t)pCypherData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC encryption mode */
CRYP_SetTDESCBCMode(hcryp, 0);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pPlainData: Pointer to the plaintext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pCypherData: Pointer to the cyphertext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES ECB decryption mode */
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode using DMA.
* @param hcryp: CRYP handle
* @param pCypherData: Pointer to the cyphertext buffer
* @param Size: Length of the plaintext buffer, must be a multiple of 8
* @param pPlainData: Pointer to the plaintext buffer
* @retval HAL status
*/
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData)
{
uint32_t inputaddr;
uint32_t outputaddr;
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS))
{
/* Process Locked */
__HAL_LOCK(hcryp);
inputaddr = (uint32_t)pCypherData;
outputaddr = (uint32_t)pPlainData;
/* Change the CRYP state */
hcryp->State = HAL_CRYP_STATE_BUSY;
/* Set CRYP peripheral in TDES CBC decryption mode */
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR);
/* Set the input and output addresses and start DMA transfer */
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr);
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
/* Return function status */
return HAL_OK;
}
else
{
return HAL_ERROR;
}
}
/**
* @}
*/
/** @defgroup CRYP_Group5 DMA callback functions
* @brief DMA callback functions.
*
@verbatim
==============================================================================
##### DMA callback functions #####
==============================================================================
[..] This section provides DMA callback functions:
(+) DMA Input data transfer complete
(+) DMA Output data transfer complete
(+) DMA error
@endverbatim
* @{
*/
/**
* @brief Input FIFO transfer completed callbacks.
* @param hcryp: CRYP handle
* @retval None
*/
__weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_CRYP_InCpltCallback could be implemented in the user file
*/
}
/**
* @brief Output FIFO transfer completed callbacks.
* @param hcryp: CRYP handle
* @retval None
*/
__weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_CRYP_OutCpltCallback could be implemented in the user file
*/
}
/**
* @brief CRYP error callbacks.
* @param hcryp: CRYP handle
* @retval None
*/
__weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp)
{
/* NOTE : This function Should not be modified, when the callback is needed,
the HAL_CRYP_ErrorCallback could be implemented in the user file
*/
}
/**
* @}
*/
/** @defgroup CRYP_Group6 CRYP IRQ handler management
* @brief CRYP IRQ handler.
*
@verbatim
==============================================================================
##### CRYP IRQ handler management #####
==============================================================================
[..] This section provides CRYP IRQ handler function.
@endverbatim
* @{
*/
/**
* @brief This function handles CRYP interrupt request.
* @param hcryp: CRYP handle
* @retval None
*/
void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp)
{
switch(CRYP->CR & CRYP_CR_ALGOMODE_DIRECTION)
{
case CRYP_CR_ALGOMODE_TDES_ECB_ENCRYPT:
HAL_CRYP_TDESECB_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_TDES_ECB_DECRYPT:
HAL_CRYP_TDESECB_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_TDES_CBC_ENCRYPT:
HAL_CRYP_TDESCBC_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_TDES_CBC_DECRYPT:
HAL_CRYP_TDESCBC_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_DES_ECB_ENCRYPT:
HAL_CRYP_DESECB_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_DES_ECB_DECRYPT:
HAL_CRYP_DESECB_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_DES_CBC_ENCRYPT:
HAL_CRYP_DESCBC_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_DES_CBC_DECRYPT:
HAL_CRYP_DESCBC_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT:
HAL_CRYP_AESECB_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_ECB_DECRYPT:
HAL_CRYP_AESECB_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT:
HAL_CRYP_AESCBC_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_CBC_DECRYPT:
HAL_CRYP_AESCBC_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT:
HAL_CRYP_AESCTR_Encrypt_IT(hcryp, NULL, 0, NULL);
break;
case CRYP_CR_ALGOMODE_AES_CTR_DECRYPT:
HAL_CRYP_AESCTR_Decrypt_IT(hcryp, NULL, 0, NULL);
break;
default:
break;
}
}
/**
* @}
*/
/** @defgroup CRYP_Group7 Peripheral State functions
* @brief Peripheral State functions.
*
@verbatim
==============================================================================
##### Peripheral State functions #####
==============================================================================
[..]
This subsection permits to get in run-time the status of the peripheral.
@endverbatim
* @{
*/
/**
* @brief Returns the CRYP state.
* @param hcryp: CRYP handle
* @retval HAL state
*/
HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp)
{
return hcryp->State;
}
/**
* @}
*/
/**
* @brief DMA CRYP Input Data process complete callback.
* @param hdma: DMA handle
* @retval None
*/
static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma)
{
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;
/* Disable the DMA transfer for input FIFO request by resetting the DIEN bit
in the DMACR register */
CRYP->DMACR &= (uint32_t)(~CRYP_DMACR_DIEN);
/* Call input data transfer complete callback */
HAL_CRYP_InCpltCallback(hcryp);
}
/**
* @brief DMA CRYP Output Data process complete callback.
* @param hdma: DMA handle
* @retval None
*/
static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma)
{
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;
/* Disable the DMA transfer for output FIFO request by resetting the DOEN bit
in the DMACR register */
CRYP->DMACR &= (uint32_t)(~CRYP_DMACR_DOEN);
/* Disable CRYP */
__HAL_CRYP_DISABLE();
/* Change the CRYP state to ready */
hcryp->State = HAL_CRYP_STATE_READY;
/* Call output data transfer complete callback */
HAL_CRYP_OutCpltCallback(hcryp);
}
/**
* @brief DMA CRYP communication error callback.
* @param hdma: DMA handle
* @retval None
*/
static void CRYP_DMAError(DMA_HandleTypeDef *hdma)
{
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent;
hcryp->State= HAL_CRYP_STATE_READY;
HAL_CRYP_ErrorCallback(hcryp);
}
/**
* @brief Writes the Key in Key registers.
* @param hcryp: CRYP handle
* @param Key: Pointer to Key buffer
* @param KeySize: Size of Key
* @retval None
*/
static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize)
{
uint32_t keyaddr = (uint32_t)Key;
switch(KeySize)
{
case CRYP_KEYSIZE_256B:
/* Key Initialisation */
CRYP->K0LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K0RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K1LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K1RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K2LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K2RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3RR = __REV(*(uint32_t*)(keyaddr));
break;
case CRYP_KEYSIZE_192B:
CRYP->K1LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K1RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K2LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K2RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3RR = __REV(*(uint32_t*)(keyaddr));
break;
case CRYP_KEYSIZE_128B:
CRYP->K2LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K2RR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3LR = __REV(*(uint32_t*)(keyaddr));
keyaddr+=4;
CRYP->K3RR = __REV(*(uint32_t*)(keyaddr));
break;
default:
break;
}
}
/**
* @brief Writes the InitVector/InitCounter in IV registers.
* @param hcryp: CRYP handle
* @param InitVector: Pointer to InitVector/InitCounter buffer
* @param IVSize: Size of the InitVector/InitCounter
* @retval None
*/
static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize)
{
uint32_t ivaddr = (uint32_t)InitVector;
switch(IVSize)
{
case CRYP_KEYSIZE_128B:
CRYP->IV0LR = __REV(*(uint32_t*)(ivaddr));
ivaddr+=4;
CRYP->IV0RR = __REV(*(uint32_t*)(ivaddr));
ivaddr+=4;
CRYP->IV1LR = __REV(*(uint32_t*)(ivaddr));
ivaddr+=4;
CRYP->IV1RR = __REV(*(uint32_t*)(ivaddr));
break;
/* Whatever key size 192 or 256, Init vector is written in IV0LR and IV0RR */
case CRYP_KEYSIZE_192B:
CRYP->IV0LR = __REV(*(uint32_t*)(ivaddr));
ivaddr+=4;
CRYP->IV0RR = __REV(*(uint32_t*)(ivaddr));
break;
case CRYP_KEYSIZE_256B:
CRYP->IV0LR = __REV(*(uint32_t*)(ivaddr));
ivaddr+=4;
CRYP->IV0RR = __REV(*(uint32_t*)(ivaddr));
break;
default:
break;
}
}
/**
* @brief Process Data: Writes Input data in polling mode and read the output data
* @param hcryp: CRYP handle
* @param Input: Pointer to the Input buffer
* @param Ilength: Length of the Input buffer, must be a multiple of 16.
* @param Output: Pointer to the returned buffer
* @retval None
*/
static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout)
{
uint32_t timeout = 0;
uint32_t i = 0;
uint32_t inputaddr = (uint32_t)Input;
uint32_t outputaddr = (uint32_t)Output;
for(i=0; (i < Ilength); i+=16)
{
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
/* Get timeout */
timeout = HAL_GetTick() + Timeout;
while(HAL_IS_BIT_CLR(CRYP->SR, CRYP_FLAG_OFNE))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
}
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Process Data: Write Input data in polling mode.
* @param hcryp: CRYP handle
* @param Input: Pointer to the Input buffer
* @param Ilength: Length of the Input buffer, must be a multiple of 8
* @param Output: Pointer to the returned buffer
* @param Timeout: Specify Timeout value
* @retval None
*/
static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout)
{
uint32_t timeout = 0;
uint32_t i = 0;
uint32_t inputaddr = (uint32_t)Input;
uint32_t outputaddr = (uint32_t)Output;
for(i=0; (i < Ilength); i+=8)
{
/* Write the Input block in the IN FIFO */
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
CRYP->DR = *(uint32_t*)(inputaddr);
inputaddr+=4;
/* Get timeout */
timeout = HAL_GetTick() + Timeout;
while(HAL_IS_BIT_CLR(CRYP->SR, CRYP_FLAG_OFNE))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
/* Change state */
hcryp->State = HAL_CRYP_STATE_TIMEOUT;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
return HAL_TIMEOUT;
}
}
}
/* Read the Output block from the Output FIFO */
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
*(uint32_t*)(outputaddr) = CRYP->DOUT;
outputaddr+=4;
}
/* Return function status */
return HAL_OK;
}
/**
* @brief Set the DMA configuration and start the DMA transfer
* @param hcryp: CRYP handle
* @param inputaddr: address of the Input buffer
* @param Size: Size of the Input buffer, must be a multiple of 16.
* @param outputaddr: address of the Output buffer
* @retval None
*/
static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr)
{
/* Set the CRYP DMA transfer complete callback */
hcryp->hdmain->XferCpltCallback = CRYP_DMAInCplt;
/* Set the DMA error callback */
hcryp->hdmain->XferErrorCallback = CRYP_DMAError;
/* Set the CRYP DMA transfer complete callback */
hcryp->hdmaout->XferCpltCallback = CRYP_DMAOutCplt;
/* Set the DMA error callback */
hcryp->hdmaout->XferErrorCallback = CRYP_DMAError;
/* Enable CRYP */
__HAL_CRYP_ENABLE();
/* Enable the DMA In DMA Stream */
HAL_DMA_Start_IT(hcryp->hdmain, inputaddr, (uint32_t)&CRYP->DR, Size/4);
/* Enable In DMA request */
CRYP->DMACR = (CRYP_DMACR_DIEN);
/* Enable the DMA Out DMA Stream */
HAL_DMA_Start_IT(hcryp->hdmaout, (uint32_t)&CRYP->DOUT, outputaddr, Size/4);
/* Enable Out DMA request */
CRYP->DMACR |= CRYP_DMACR_DOEN;
}
/**
* @brief Sets the CRYP peripheral in DES ECB mode.
* @param hcryp: CRYP handle
* @param Direction: Encryption or decryption
* @retval None
*/
static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)
{
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_DES_ECB | Direction);
/* Set the key */
CRYP->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey));
CRYP->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4));
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
}
/**
* @brief Sets the CRYP peripheral in DES CBC mode.
* @param hcryp: CRYP handle
* @param Direction: Encryption or decryption
* @retval None
*/
static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)
{
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_DES_CBC | Direction);
/* Set the key */
CRYP->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey));
CRYP->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4));
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
}
/**
* @brief Sets the CRYP peripheral in TDES ECB mode.
* @param hcryp: CRYP handle
* @param Direction: Encryption or decryption
* @retval None
*/
static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)
{
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the CRYP peripheral in AES ECB mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_TDES_ECB | Direction);
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
}
/**
* @brief Sets the CRYP peripheral in TDES CBC mode
* @param hcryp: CRYP handle
* @param Direction: Encryption or decryption
* @retval None
*/
static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction)
{
/* Check if initialization phase has already been performed */
if(hcryp->Phase == HAL_CRYP_PHASE_READY)
{
/* Set the CRYP peripheral in AES CBC mode */
__HAL_CRYP_SET_MODE(CRYP_CR_ALGOMODE_TDES_CBC | Direction);
/* Set the key */
CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B);
/* Set the Initialization Vector */
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B);
/* Flush FIFO */
__HAL_CRYP_FIFO_FLUSH();
/* Set the phase */
hcryp->Phase = HAL_CRYP_PHASE_PROCESS;
}
}
/**
* @}
*/
#endif /* STM32F415xx || STM32F417xx || STM32F437xx || STM32F439xx */
#endif /* HAL_CRYP_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/