ref: 2a7a75f8f98d051f8d2b7b78d31649e943329fa6
dir: /demos/stm32f429_disco/stm/stm32f4_spl/src/stm32f4xx_ll_fsmc.c/
/**
******************************************************************************
* @file stm32f4xx_ll_fsmc.c
* @author MCD Application Team
* @version V1.0.0
* @date 18-February-2014
* @brief FSMC Low Layer HAL module driver.
*
* This file provides firmware functions to manage the following
* functionalities of the Flexible Static Memory Controller (FSMC) peripheral memories:
* + Initialization/de-initialization functions
* + Peripheral Control functions
* + Peripheral State functions
*
@verbatim
==============================================================================
##### FSMC peripheral features #####
==============================================================================
[..] The Flexible static memory controller (FSMC) includes two memory controllers:
(+) The NOR/PSRAM memory controller
(+) The NAND/PC Card memory controller
[..] The FSMC functional block makes the interface with synchronous and asynchronous static
memories, SDRAM memories, and 16-bit PC memory cards. Its main purposes are:
(+) to translate AHB transactions into the appropriate external device protocol.
(+) to meet the access time requirements of the external memory devices.
[..] All external memories share the addresses, data and control signals with the controller.
Each external device is accessed by means of a unique Chip Select. The FSMC performs
only one access at a time to an external device.
The main features of the FSMC controller are the following:
(+) Interface with static-memory mapped devices including:
(++) Static random access memory (SRAM).
(++) Read-only memory (ROM).
(++) NOR Flash memory/OneNAND Flash memory.
(++) PSRAM (4 memory banks).
(++) 16-bit PC Card compatible devices.
(++) Two banks of NAND Flash memory with ECC hardware to check up to 8 Kbytes of
data.
(+) Independent Chip Select control for each memory bank.
(+) Independent configuration for each memory bank.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @defgroup FSMC
* @brief FSMC driver modules
* @{
*/
#if defined (HAL_SRAM_MODULE_ENABLED) || defined(HAL_NOR_MODULE_ENABLED) || defined(HAL_NAND_MODULE_ENABLED) || defined(HAL_PCCARD_MODULE_ENABLED)
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup FSMC_Private_Functions
* @{
*/
/** @defgroup FSMC_NORSRAM Controller functions
* @brief NORSRAM Controller functions
*
@verbatim
==============================================================================
##### How to use NORSRAM device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FSMC NORSRAM banks in order
to run the NORSRAM external devices.
(+) FSMC NORSRAM bank reset using the function FSMC_NORSRAM_DeInit()
(+) FSMC NORSRAM bank control configuration using the function FSMC_NORSRAM_Init()
(+) FSMC NORSRAM bank timing configuration using the function FSMC_NORSRAM_Timing_Init()
(+) FSMC NORSRAM bank extended timing configuration using the function
FSMC_NORSRAM_Extended_Timing_Init()
(+) FSMC NORSRAM bank enable/disable write operation using the functions
FSMC_NORSRAM_WriteOperation_Enable()/FSMC_NORSRAM_WriteOperation_Disable()
@endverbatim
* @{
*/
/** @defgroup HAL_FSMC_NORSRAM_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FSMC NORSRAM interface
(+) De-initialize the FSMC NORSRAM interface
(+) Configure the FSMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initialize the FSMC_NORSRAM device according to the specified
* control parameters in the FSMC_NORSRAM_InitTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Init: Pointer to NORSRAM Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_Init(FSMC_NORSRAM_TypeDef *Device, FSMC_NORSRAM_InitTypeDef* Init)
{
uint32_t tmpr = 0;
/* Check the parameters */
assert_param(IS_FSMC_NORSRAM_BANK(Init->NSBank));
assert_param(IS_FSMC_MUX(Init->DataAddressMux));
assert_param(IS_FSMC_MEMORY(Init->MemoryType));
assert_param(IS_FSMC_NORSRAM_MEMORY_WIDTH(Init->MemoryDataWidth));
assert_param(IS_FSMC_BURSTMODE(Init->BurstAccessMode));
assert_param(IS_FSMC_WAIT_POLARITY(Init->WaitSignalPolarity));
assert_param(IS_FSMC_WRAP_MODE(Init->WrapMode));
assert_param(IS_FSMC_WAIT_SIGNAL_ACTIVE(Init->WaitSignalActive));
assert_param(IS_FSMC_WRITE_OPERATION(Init->WriteOperation));
assert_param(IS_FSMC_WAITE_SIGNAL(Init->WaitSignal));
assert_param(IS_FSMC_EXTENDED_MODE(Init->ExtendedMode));
assert_param(IS_FSMC_ASYNWAIT(Init->AsynchronousWait));
assert_param(IS_FSMC_WRITE_BURST(Init->WriteBurst));
/* Set NORSRAM device control parameters */
tmpr = (uint32_t)(Init->DataAddressMux |\
Init->MemoryType |\
Init->MemoryDataWidth |\
Init->BurstAccessMode |\
Init->WaitSignalPolarity |\
Init->WrapMode |\
Init->WaitSignalActive |\
Init->WriteOperation |\
Init->WaitSignal |\
Init->ExtendedMode |\
Init->AsynchronousWait |\
Init->WriteBurst
);
if(Init->MemoryType == FSMC_MEMORY_TYPE_NOR)
{
tmpr |= (uint32_t)FSMC_NORSRAM_FLASH_ACCESS_ENABLE;
}
Device->BTCR[Init->NSBank] = tmpr;
return HAL_OK;
}
/**
* @brief DeInitialize the FSMC_NORSRAM peripheral
* @param Device: Pointer to NORSRAM device instance
* @param ExDevice: Pointer to NORSRAM extended mode device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_DeInit(FSMC_NORSRAM_TypeDef *Device, FSMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FSMC_NORSRAM_DEVICE(Device));
assert_param(IS_FSMC_NORSRAM_EXTENDED_DEVICE(ExDevice));
/* Disable the FSMC_NORSRAM device */
__FSMC_NORSRAM_DISABLE(Device, Bank);
/* De-initialize the FSMC_NORSRAM device */
/* FSMC_NORSRAM_BANK1 */
if(Bank == FSMC_NORSRAM_BANK1)
{
Device->BTCR[Bank] = 0x000030DB;
}
/* FSMC_NORSRAM_BANK2, FSMC_NORSRAM_BANK3 or FSMC_NORSRAM_BANK4 */
else
{
Device->BTCR[Bank] = 0x000030D2;
}
Device->BTCR[Bank + 1] = 0x0FFFFFFF;
ExDevice->BWTR[Bank] = 0x0FFFFFFF;
return HAL_OK;
}
/**
* @brief Initialize the FSMC_NORSRAM Timing according to the specified
* parameters in the FSMC_NORSRAM_TimingTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Timing: Pointer to NORSRAM Timing structure
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_Timing_Init(FSMC_NORSRAM_TypeDef *Device, FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmpr = 0;
/* Check the parameters */
assert_param(IS_FSMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime));
assert_param(IS_FSMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime));
assert_param(IS_FSMC_DATASETUP_TIME(Timing->DataSetupTime));
assert_param(IS_FSMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration));
assert_param(IS_FSMC_CLK_DIV(Timing->CLKDivision));
assert_param(IS_FSMC_DATA_LATENCY(Timing->DataLatency));
assert_param(IS_FSMC_ACCESS_MODE(Timing->AccessMode));
/* Set FSMC_NORSRAM device timing parameters */
tmpr = (uint32_t)(Timing->AddressSetupTime |\
((Timing->AddressHoldTime) << 4) |\
((Timing->DataSetupTime) << 8) |\
((Timing->BusTurnAroundDuration) << 16) |\
(((Timing->CLKDivision)-1) << 20) |\
(((Timing->DataLatency)-2) << 24) |\
(Timing->AccessMode)
);
Device->BTCR[Bank + 1] = tmpr;
return HAL_OK;
}
/**
* @brief Initialize the FSMC_NORSRAM Extended mode Timing according to the specified
* parameters in the FSMC_NORSRAM_TimingTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Timing: Pointer to NORSRAM Timing structure
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_Extended_Timing_Init(FSMC_NORSRAM_EXTENDED_TypeDef *Device, FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank, uint32_t ExtendedMode)
{
/* Set NORSRAM device timing register for write configuration, if extended mode is used */
if(ExtendedMode == FSMC_EXTENDED_MODE_ENABLE)
{
/* Check the parameters */
assert_param(IS_FSMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime));
assert_param(IS_FSMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime));
assert_param(IS_FSMC_DATASETUP_TIME(Timing->DataSetupTime));
assert_param(IS_FSMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration));
assert_param(IS_FSMC_CLK_DIV(Timing->CLKDivision));
assert_param(IS_FSMC_DATA_LATENCY(Timing->DataLatency));
assert_param(IS_FSMC_ACCESS_MODE(Timing->AccessMode));
Device->BWTR[Bank] = (uint32_t)(Timing->AddressSetupTime |\
((Timing->AddressHoldTime) << 4) |\
((Timing->DataSetupTime) << 8) |\
((Timing->BusTurnAroundDuration) << 16) |\
(((Timing->CLKDivision)-1) << 20) |\
(((Timing->DataLatency)-2) << 24) |\
(Timing->AccessMode));
}
else
{
Device->BWTR[Bank] = 0x0FFFFFFF;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup HAL_FSMC_NORSRAM_Group3 Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### FSMC_NORSRAM Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the FSMC NORSRAM interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically FSMC_NORSRAM write operation.
* @param Device: Pointer to NORSRAM device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_WriteOperation_Enable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank)
{
/* Enable write operation */
Device->BTCR[Bank] |= FSMC_WRITE_OPERATION_ENABLE;
return HAL_OK;
}
/**
* @brief Disables dynamically FSMC_NORSRAM write operation.
* @param Device: Pointer to NORSRAM device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NORSRAM_WriteOperation_Disable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank)
{
/* Disable write operation */
Device->BTCR[Bank] &= ~FSMC_WRITE_OPERATION_ENABLE;
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
/** @defgroup FSMC_PCCARD Controller functions
* @brief PCCARD Controller functions
*
@verbatim
==============================================================================
##### How to use NAND device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FSMC NAND banks in order
to run the NAND external devices.
(+) FSMC NAND bank reset using the function FSMC_NAND_DeInit()
(+) FSMC NAND bank control configuration using the function FSMC_NAND_Init()
(+) FSMC NAND bank common space timing configuration using the function
FSMC_NAND_CommonSpace_Timing_Init()
(+) FSMC NAND bank attribute space timing configuration using the function
FSMC_NAND_AttributeSpace_Timing_Init()
(+) FSMC NAND bank enable/disable ECC correction feature using the functions
FSMC_NAND_ECC_Enable()/FSMC_NAND_ECC_Disable()
(+) FSMC NAND bank get ECC correction code using the function FSMC_NAND_GetECC()
@endverbatim
* @{
*/
/** @defgroup HAL_FSMC_NAND_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FSMC NAND interface
(+) De-initialize the FSMC NAND interface
(+) Configure the FSMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initializes the FSMC_NAND device according to the specified
* control parameters in the FSMC_NAND_HandleTypeDef
* @param Device: Pointer to NAND device instance
* @param Init: Pointer to NAND Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_Init(FSMC_NAND_TypeDef *Device, FSMC_NAND_InitTypeDef *Init)
{
uint32_t tmppcr = 0;
/* Check the parameters */
assert_param(IS_FSMC_NAND_BANK(Init->NandBank));
assert_param(IS_FSMC_WAIT_FEATURE(Init->Waitfeature));
assert_param(IS_FSMC_NAND_MEMORY_WIDTH(Init->MemoryDataWidth));
assert_param(IS_FSMC_ECC_STATE(Init->EccComputation));
assert_param(IS_FSMC_ECCPAGE_SIZE(Init->ECCPageSize));
assert_param(IS_FSMC_TCLR_TIME(Init->TCLRSetupTime));
assert_param(IS_FSMC_TAR_TIME(Init->TARSetupTime));
/* Set NAND device control parameters */
tmppcr = (uint32_t)(Init->Waitfeature |\
FSMC_PCR_MEMORY_TYPE_NAND |\
Init->MemoryDataWidth |\
Init->EccComputation |\
Init->ECCPageSize |\
((Init->TCLRSetupTime) << 9) |\
((Init->TARSetupTime) << 13)
);
if(Init->NandBank == FSMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PCR2 = tmppcr;
}
else
{
/* NAND bank 3 registers configuration */
Device->PCR3 = tmppcr;
}
return HAL_OK;
}
/**
* @brief Initializes the FSMC_NAND Common space Timing according to the specified
* parameters in the FSMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to NAND device instance
* @param Timing: Pointer to NAND timing structure
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_CommonSpace_Timing_Init(FSMC_NAND_TypeDef *Device, FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmppmem = 0;
/* Check the parameters */
assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set FSMC_NAND device timing parameters */
tmppmem = (uint32_t)(Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
((Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
if(Bank == FSMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PMEM2 = tmppmem;
}
else
{
/* NAND bank 3 registers configuration */
Device->PMEM3 = tmppmem;
}
return HAL_OK;
}
/**
* @brief Initializes the FSMC_NAND Attribute space Timing according to the specified
* parameters in the FSMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to NAND device instance
* @param Timing: Pointer to NAND timing structure
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_AttributeSpace_Timing_Init(FSMC_NAND_TypeDef *Device, FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmppatt = 0;
/* Check the parameters */
assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set FSMC_NAND device timing parameters */
tmppatt = (uint32_t)(Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
((Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
if(Bank == FSMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PATT2 = tmppatt;
}
else
{
/* NAND bank 3 registers configuration */
Device->PATT3 = tmppatt;
}
return HAL_OK;
}
/**
* @brief DeInitializes the FSMC_NAND device
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_DeInit(FSMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Disable the NAND Bank */
__FSMC_NAND_DISABLE(Device, Bank);
/* De-initialize the NAND Bank */
if(Bank == FSMC_NAND_BANK2)
{
/* Set the FSMC_NAND_BANK2 registers to their reset values */
Device->PCR2 = 0x00000018;
Device->SR2 = 0x00000040;
Device->PMEM2 = 0xFCFCFCFC;
Device->PATT2 = 0xFCFCFCFC;
}
/* FSMC_Bank3_NAND */
else
{
/* Set the FSMC_NAND_BANK3 registers to their reset values */
Device->PCR3 = 0x00000018;
Device->SR3 = 0x00000040;
Device->PMEM3 = 0xFCFCFCFC;
Device->PATT3 = 0xFCFCFCFC;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup HAL_FSMC_NAND_Group3 Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### FSMC_NAND Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the FSMC NAND interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically FSMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_ECC_Enable(FSMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Enable ECC feature */
if(Bank == FSMC_NAND_BANK2)
{
Device->PCR2 |= FSMC_PCR2_ECCEN;
}
else
{
Device->PCR3 |= FSMC_PCR3_ECCEN;
}
return HAL_OK;
}
/**
* @brief Disables dynamically FSMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_ECC_Disable(FSMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Disable ECC feature */
if(Bank == FSMC_NAND_BANK2)
{
Device->PCR2 &= ~FSMC_PCR2_ECCEN;
}
else
{
Device->PCR3 &= ~FSMC_PCR3_ECCEN;
}
return HAL_OK;
}
/**
* @brief Disables dynamically FSMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param ECCval: Pointer to ECC value
* @param Bank: NAND bank number
* @param Timeout: Timeout wait value
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_NAND_GetECC(FSMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank, uint32_t Timeout)
{
uint32_t timeout = 0;
/* Check the parameters */
assert_param(IS_FSMC_NAND_DEVICE(Device));
assert_param(IS_FSMC_NAND_BANK(Bank));
timeout = HAL_GetTick() + Timeout;
/* Wait untill FIFO is empty */
while(__FSMC_NAND_GET_FLAG(Device, Bank, FSMC_FLAG_FEMPT))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
return HAL_TIMEOUT;
}
}
}
if(Bank == FSMC_NAND_BANK2)
{
/* Get the ECCR2 register value */
*ECCval = (uint32_t)Device->ECCR2;
}
else
{
/* Get the ECCR3 register value */
*ECCval = (uint32_t)Device->ECCR3;
}
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
/** @defgroup FSMC_PCCARD Controller functions
* @brief PCCARD Controller functions
*
@verbatim
==============================================================================
##### How to use PCCARD device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FSMC PCCARD bank in order
to run the PCCARD/compact flash external devices.
(+) FSMC PCCARD bank reset using the function FSMC_PCCARD_DeInit()
(+) FSMC PCCARD bank control configuration using the function FSMC_PCCARD_Init()
(+) FSMC PCCARD bank common space timing configuration using the function
FSMC_PCCARD_CommonSpace_Timing_Init()
(+) FSMC PCCARD bank attribute space timing configuration using the function
FSMC_PCCARD_AttributeSpace_Timing_Init()
(+) FSMC PCCARD bank IO space timing configuration using the function
FSMC_PCCARD_IOSpace_Timing_Init()
@endverbatim
* @{
*/
/** @defgroup HAL_FSMC_PCCARD_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FSMC PCCARD interface
(+) De-initialize the FSMC PCCARD interface
(+) Configure the FSMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initializes the FSMC_PCCARD device according to the specified
* control parameters in the FSMC_PCCARD_HandleTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Init: Pointer to PCCARD Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_PCCARD_Init(FSMC_PCCARD_TypeDef *Device, FSMC_PCCARD_InitTypeDef *Init)
{
/* Check the parameters */
assert_param(IS_FSMC_WAIT_FEATURE(Init->Waitfeature));
assert_param(IS_FSMC_TCLR_TIME(Init->TCLRSetupTime));
assert_param(IS_FSMC_TAR_TIME(Init->TARSetupTime));
/* Set FSMC_PCCARD device control parameters */
Device->PCR4 = (uint32_t)(Init->Waitfeature |\
FSMC_NAND_PCC_MEM_BUS_WIDTH_16 |\
(Init->TCLRSetupTime << 9) |\
(Init->TARSetupTime << 13));
return HAL_OK;
}
/**
* @brief Initializes the FSMC_PCCARD Common space Timing according to the specified
* parameters in the FSMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_PCCARD_CommonSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, FSMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set PCCARD timing parameters */
Device->PMEM4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief Initializes the FSMC_PCCARD Attribute space Timing according to the specified
* parameters in the FSMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_PCCARD_AttributeSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, FSMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set PCCARD timing parameters */
Device->PATT4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief Initializes the FSMC_PCCARD IO space Timing according to the specified
* parameters in the FSMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_PCCARD_IOSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device, FSMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FSMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FSMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FSMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FSMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set FSMC_PCCARD device timing parameters */
Device->PIO4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief DeInitializes the FSMC_PCCARD device
* @param Device: Pointer to PCCARD device instance
* @retval HAL status
*/
HAL_StatusTypeDef FSMC_PCCARD_DeInit(FSMC_PCCARD_TypeDef *Device)
{
/* Disable the FSMC_PCCARD device */
__FSMC_PCCARD_DISABLE(Device);
/* De-initialize the FSMC_PCCARD device */
Device->PCR4 = 0x00000018;
Device->SR4 = 0x00000000;
Device->PMEM4 = 0xFCFCFCFC;
Device->PATT4 = 0xFCFCFCFC;
Device->PIO4 = 0xFCFCFCFC;
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */
#endif /* HAL_FSMC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/