ref: 504fa350e718a379f4a0ae764a80d1d8dd1b959b
dir: /demos/stm32f429_disco/stm/stm32f429/stm32f429i_discovery_sdram.c/
/**
******************************************************************************
* @file stm32f429i_discovery_sdram.c
* @author MCD Application Team
* @version V2.0.1
* @date 26-February-2014
* @brief This file provides a set of functions needed to drive the
* IS42S16400J SDRAM memory mounted on STM32F429I-DISCO Kit.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f429i_discovery_sdram.h"
/** @addtogroup BSP
* @{
*/
/** @addtogroup STM32F429I_DISCOVERY
* @{
*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM STM32F429I_DISCOVERY_SDRAM
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Types_Definitions STM32F429I_DISCOVERY_SDRAM_Private_Types_Definitions
* @{
*/
/**
* @}
*/
/* Private define ------------------------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Defines STM32F429I_DISCOVERY_SDRAM_Private_Defines
* @{
*/
/**
* @}
*/
/* Private macro -------------------------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Macros STM32F429I_DISCOVERY_SDRAM_Private_Macros
* @{
*/
/**
* @}
*/
/* Private variables ---------------------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Variables STM32F429I_DISCOVERY_SDRAM_Private_Variables
* @{
*/
static SDRAM_HandleTypeDef SdramHandle;
static FMC_SDRAM_TimingTypeDef Timing;
static FMC_SDRAM_CommandTypeDef Command;
/**
* @}
*/
/* Private function prototypes -----------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Function_Prototypes STM32F429I_DISCOVERY_SDRAM_Private_Function_Prototypes
* @{
*/
static void MspInit(void);
/**
* @}
*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup STM32F429I_DISCOVERY_SDRAM_Private_Functions STM32F429I_DISCOVERY_SDRAM_Private_Functions
* @{
*/
/**
* @brief Initializes the SDRAM device.
* @param None
* @retval None
*/
void BSP_SDRAM_Init(void)
{
/* SDRAM device configuration */
SdramHandle.Instance = FMC_SDRAM_DEVICE;
/* FMC Configuration ---------------------------------------------------------*/
/* FMC SDRAM Bank configuration */
/* Timing configuration for 90 Mhz of SD clock frequency (180Mhz/2) */
/* TMRD: 2 Clock cycles */
Timing.LoadToActiveDelay = 2;
/* TXSR: min=70ns (7x11.11ns) */
Timing.ExitSelfRefreshDelay = 7;
/* TRAS: min=42ns (4x11.11ns) max=120k (ns) */
Timing.SelfRefreshTime = 4;
/* TRC: min=70 (7x11.11ns) */
Timing.RowCycleDelay = 7;
/* TWR: min=1+ 7ns (1+1x11.11ns) */
Timing.WriteRecoveryTime = 2;
/* TRP: 20ns => 2x11.11ns*/
Timing.RPDelay = 2;
/* TRCD: 20ns => 2x11.11ns */
Timing.RCDDelay = 2;
/* FMC SDRAM control configuration */
SdramHandle.Init.SDBank = FMC_SDRAM_BANK2;
/* Row addressing: [7:0] */
SdramHandle.Init.ColumnBitsNumber = FMC_SDRAM_COLUMN_BITS_NUM_8;
/* Column addressing: [11:0] */
SdramHandle.Init.RowBitsNumber = FMC_SDRAM_ROW_BITS_NUM_12;
SdramHandle.Init.MemoryDataWidth = SDRAM_MEMORY_WIDTH;
SdramHandle.Init.InternalBankNumber = FMC_SDRAM_INTERN_BANKS_NUM_4;
SdramHandle.Init.CASLatency = SDRAM_CAS_LATENCY;
SdramHandle.Init.WriteProtection = FMC_SDRAM_WRITE_PROTECTION_DISABLE;
SdramHandle.Init.SDClockPeriod = SDCLOCK_PERIOD;
SdramHandle.Init.ReadBurst = SDRAM_READBURST;
SdramHandle.Init.ReadPipeDelay = FMC_SDRAM_RPIPE_DELAY_1;
/* SDRAM controller initialization */
MspInit();
HAL_SDRAM_Init(&SdramHandle, &Timing);
/* SDRAM initialization sequence */
BSP_SDRAM_Initialization_sequence(REFRESH_COUNT);
}
/**
* @brief Programs the SDRAM device.
* @param RefreshCount: SDRAM refresh counter value
* @retval None
*/
void BSP_SDRAM_Initialization_sequence(uint32_t RefreshCount)
{
__IO uint32_t tmpmrd =0;
/* Step 1: Configure a clock configuration enable command */
Command.CommandMode = FMC_SDRAM_CMD_CLK_ENABLE;
Command.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
Command.AutoRefreshNumber = 1;
Command.ModeRegisterDefinition = 0;
/* Send the command */
HAL_SDRAM_SendCommand(&SdramHandle, &Command, SDRAM_TIMEOUT);
/* Step 2: Insert 100 us minimum delay */
/* Inserted delay is equal to 1 ms due to systick time base unit (ms) */
HAL_Delay(1);
/* Step 3: Configure a PALL (precharge all) command */
Command.CommandMode = FMC_SDRAM_CMD_PALL;
Command.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
Command.AutoRefreshNumber = 1;
Command.ModeRegisterDefinition = 0;
/* Send the command */
HAL_SDRAM_SendCommand(&SdramHandle, &Command, SDRAM_TIMEOUT);
/* Step 4: Configure an Auto Refresh command */
Command.CommandMode = FMC_SDRAM_CMD_AUTOREFRESH_MODE;
Command.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
Command.AutoRefreshNumber = 4;
Command.ModeRegisterDefinition = 0;
/* Send the command */
HAL_SDRAM_SendCommand(&SdramHandle, &Command, SDRAM_TIMEOUT);
/* Step 5: Program the external memory mode register */
tmpmrd = (uint32_t)SDRAM_MODEREG_BURST_LENGTH_2 |
SDRAM_MODEREG_BURST_TYPE_SEQUENTIAL |
SDRAM_MODEREG_CAS_LATENCY_3 |
SDRAM_MODEREG_OPERATING_MODE_STANDARD |
SDRAM_MODEREG_WRITEBURST_MODE_SINGLE;
Command.CommandMode = FMC_SDRAM_CMD_LOAD_MODE;
Command.CommandTarget = FMC_SDRAM_CMD_TARGET_BANK2;
Command.AutoRefreshNumber = 1;
Command.ModeRegisterDefinition = tmpmrd;
/* Send the command */
HAL_SDRAM_SendCommand(&SdramHandle, &Command, SDRAM_TIMEOUT);
/* Step 6: Set the refresh rate counter */
/* Set the device refresh rate */
HAL_SDRAM_ProgramRefreshRate(&SdramHandle, RefreshCount);
}
/**
* @brief Reads an mount of data from the SDRAM memory in polling mode.
* @param uwStartAddress : Read start address
* @param pData : Pointer to data to be read
* @param uwDataSize: Size of read data from the memory
* @retval None
*/
void BSP_SDRAM_ReadData(uint32_t uwStartAddress, uint32_t* pData, uint32_t uwDataSize)
{
HAL_SDRAM_Read_32b(&SdramHandle, (uint32_t *)uwStartAddress, pData, uwDataSize);
}
/**
* @brief Reads an mount of data from the SDRAM memory in DMA mode.
* @param uwStartAddress : Read start address
* @param pData : Pointer to data to be read
* @param uwDataSize: Size of read data from the memory
* @retval None
*/
void BSP_SDRAM_ReadData_DMA(uint32_t uwStartAddress, uint32_t* pData, uint32_t uwDataSize)
{
HAL_SDRAM_Read_DMA(&SdramHandle, (uint32_t *)uwStartAddress, pData, uwDataSize);
}
/**
* @brief Writes an mount of data to the SDRAM memory in polling mode.
* @param uwStartAddress : Write start address
* @param pData : Pointer to data to be written
* @param uwDataSize: Size of written data from the memory
* @retval None
*/
void BSP_SDRAM_WriteData(uint32_t uwStartAddress, uint32_t* pData, uint32_t uwDataSize)
{
/* Disable write protection */
HAL_SDRAM_WriteProtection_Disable(&SdramHandle);
/*Write 32-bit data buffer to SDRAM memory*/
HAL_SDRAM_Write_32b(&SdramHandle, (uint32_t *)uwStartAddress, pData, uwDataSize);
}
/**
* @brief Writes an mount of data to the SDRAM memory in DMA mode.
* @param uwStartAddress : Write start address
* @param pData : Pointer to data to be written
* @param uwDataSize: Size of written data from the memory
* @retval None
*/
void BSP_SDRAM_WriteData_DMA(uint32_t uwStartAddress, uint32_t* pData, uint32_t uwDataSize)
{
HAL_SDRAM_Write_DMA(&SdramHandle, (uint32_t *)uwStartAddress, pData, uwDataSize);
}
/**
* @brief Sends command to the SDRAM bank.
* @param SdramCmd: Pointer to SDRAM command structure
* @retval HAL status
*/
HAL_StatusTypeDef BSP_SDRAM_Sendcmd(FMC_SDRAM_CommandTypeDef *SdramCmd)
{
return(HAL_SDRAM_SendCommand(&SdramHandle, SdramCmd, SDRAM_TIMEOUT));
}
/**
* @brief Handles SDRAM DMA transfer interrupt request.
* @param None
* @retval None
*/
void BSP_SDRAM_DMA_IRQHandler(void)
{
HAL_DMA_IRQHandler(SdramHandle.hdma);
}
/**
* @brief Initializes SDRAM MSP.
* @param None
* @retval None
*/
static void MspInit(void)
{
static DMA_HandleTypeDef dmaHandle;
GPIO_InitTypeDef GPIO_InitStructure;
SDRAM_HandleTypeDef *hsdram = &SdramHandle;
/* Enable FMC clock */
__FMC_CLK_ENABLE();
/* Enable chosen DMAx clock */
__DMAx_CLK_ENABLE();
/* Enable GPIOs clock */
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
/*-- GPIOs Configuration -----------------------------------------------------*/
/*
+-------------------+--------------------+--------------------+--------------------+
+ SDRAM pins assignment +
+-------------------+--------------------+--------------------+--------------------+
| PD0 <-> FMC_D2 | PE0 <-> FMC_NBL0 | PF0 <-> FMC_A0 | PG0 <-> FMC_A10 |
| PD1 <-> FMC_D3 | PE1 <-> FMC_NBL1 | PF1 <-> FMC_A1 | PG1 <-> FMC_A11 |
| PD8 <-> FMC_D13 | PE7 <-> FMC_D4 | PF2 <-> FMC_A2 | PG8 <-> FMC_SDCLK |
| PD9 <-> FMC_D14 | PE8 <-> FMC_D5 | PF3 <-> FMC_A3 | PG15 <-> FMC_NCAS |
| PD10 <-> FMC_D15 | PE9 <-> FMC_D6 | PF4 <-> FMC_A4 |--------------------+
| PD14 <-> FMC_D0 | PE10 <-> FMC_D7 | PF5 <-> FMC_A5 |
| PD15 <-> FMC_D1 | PE11 <-> FMC_D8 | PF11 <-> FMC_NRAS |
+-------------------| PE12 <-> FMC_D9 | PF12 <-> FMC_A6 |
| PE13 <-> FMC_D10 | PF13 <-> FMC_A7 |
| PE14 <-> FMC_D11 | PF14 <-> FMC_A8 |
| PE15 <-> FMC_D12 | PF15 <-> FMC_A9 |
+-------------------+--------------------+--------------------+
| PB5 <-> FMC_SDCKE1|
| PB6 <-> FMC_SDNE1 |
| PC0 <-> FMC_SDNWE |
+-------------------+
*/
/* Common GPIO configuration */
GPIO_InitStructure.Mode = GPIO_MODE_AF_PP;
GPIO_InitStructure.Speed = GPIO_SPEED_FAST;
GPIO_InitStructure.Pull = GPIO_NOPULL;
GPIO_InitStructure.Alternate = GPIO_AF12_FMC;
/* GPIOB configuration */
GPIO_InitStructure.Pin = GPIO_PIN_5 | GPIO_PIN_6;
HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
/* GPIOC configuration */
GPIO_InitStructure.Pin = GPIO_PIN_0;
HAL_GPIO_Init(GPIOC, &GPIO_InitStructure);
/* GPIOD configuration */
GPIO_InitStructure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_8 |
GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_14 |
GPIO_PIN_15;
HAL_GPIO_Init(GPIOD, &GPIO_InitStructure);
/* GPIOE configuration */
GPIO_InitStructure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_7 |
GPIO_PIN_8 | GPIO_PIN_9 | GPIO_PIN_10 |
GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 |
GPIO_PIN_14 | GPIO_PIN_15;
HAL_GPIO_Init(GPIOE, &GPIO_InitStructure);
/* GPIOF configuration */
GPIO_InitStructure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 |
GPIO_PIN_3 | GPIO_PIN_4 | GPIO_PIN_5 |
GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 |
GPIO_PIN_14 | GPIO_PIN_15;
HAL_GPIO_Init(GPIOF, &GPIO_InitStructure);
/* GPIOG configuration */
GPIO_InitStructure.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_4 |
GPIO_PIN_5 | GPIO_PIN_8 | GPIO_PIN_15;
HAL_GPIO_Init(GPIOG, &GPIO_InitStructure);
/* Configure common DMA parameters */
dmaHandle.Init.Channel = SDRAM_DMAx_CHANNEL;
dmaHandle.Init.Direction = DMA_MEMORY_TO_MEMORY;
dmaHandle.Init.PeriphInc = DMA_PINC_ENABLE;
dmaHandle.Init.MemInc = DMA_MINC_ENABLE;
dmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
dmaHandle.Init.MemDataAlignment = DMA_MDATAALIGN_WORD;
dmaHandle.Init.Mode = DMA_NORMAL;
dmaHandle.Init.Priority = DMA_PRIORITY_HIGH;
dmaHandle.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
dmaHandle.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_FULL;
dmaHandle.Init.MemBurst = DMA_MBURST_SINGLE;
dmaHandle.Init.PeriphBurst = DMA_PBURST_SINGLE;
dmaHandle.Instance = SDRAM_DMAx_STREAM;
/* Associate the DMA handle */
__HAL_LINKDMA(hsdram, hdma, dmaHandle);
/* Deinitialize the stream for new transfer */
HAL_DMA_DeInit(&dmaHandle);
/* Configure the DMA stream */
HAL_DMA_Init(&dmaHandle);
/* NVIC configuration for DMA transfer complete interrupt */
HAL_NVIC_SetPriority(SDRAM_DMAx_IRQn, 0, 0);
HAL_NVIC_EnableIRQ(SDRAM_DMAx_IRQn);
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/