ref: 6e79cef4b05e2863fef1eb0da4de7a4afc920494
dir: /demos/stm32f429_disco/stm/stm32f4_spl/src/stm32f4xx_ll_fmc.c/
/**
******************************************************************************
* @file stm32f4xx_ll_fmc.c
* @author MCD Application Team
* @version V1.0.0
* @date 18-February-2014
* @brief FMC Low Layer HAL module driver.
*
* This file provides firmware functions to manage the following
* functionalities of the Flexible Memory Controller (FMC) peripheral memories:
* + Initialization/de-initialization functions
* + Peripheral Control functions
* + Peripheral State functions
*
@verbatim
==============================================================================
##### FMC peripheral features #####
==============================================================================
[..] The Flexible memory controller (FMC) includes three memory controllers:
(+) The NOR/PSRAM memory controller
(+) The NAND/PC Card memory controller
(+) The Synchronous DRAM (SDRAM) controller
[..] The FMC functional block makes the interface with synchronous and asynchronous static
memories, SDRAM memories, and 16-bit PC memory cards. Its main purposes are:
(+) to translate AHB transactions into the appropriate external device protocol
(+) to meet the access time requirements of the external memory devices
[..] All external memories share the addresses, data and control signals with the controller.
Each external device is accessed by means of a unique Chip Select. The FMC performs
only one access at a time to an external device.
The main features of the FMC controller are the following:
(+) Interface with static-memory mapped devices including:
(++) Static random access memory (SRAM)
(++) Read-only memory (ROM)
(++) NOR Flash memory/OneNAND Flash memory
(++) PSRAM (4 memory banks)
(++) 16-bit PC Card compatible devices
(++) Two banks of NAND Flash memory with ECC hardware to check up to 8 Kbytes of
data
(+) Interface with synchronous DRAM (SDRAM) memories
(+) Independent Chip Select control for each memory bank
(+) Independent configuration for each memory bank
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_hal.h"
/** @addtogroup STM32F4xx_HAL_Driver
* @{
*/
/** @defgroup FMC
* @brief FMC driver modules
* @{
*/
#if defined (HAL_SRAM_MODULE_ENABLED) || defined(HAL_NOR_MODULE_ENABLED) || defined(HAL_NAND_MODULE_ENABLED) || defined(HAL_PCCARD_MODULE_ENABLED) || defined(HAL_SDRAM_MODULE_ENABLED)
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup FMC_Private_Functions
* @{
*/
/** @defgroup FMC_NORSRAM Controller functions
* @brief NORSRAM Controller functions
*
@verbatim
==============================================================================
##### How to use NORSRAM device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FMC NORSRAM banks in order
to run the NORSRAM external devices.
(+) FMC NORSRAM bank reset using the function FMC_NORSRAM_DeInit()
(+) FMC NORSRAM bank control configuration using the function FMC_NORSRAM_Init()
(+) FMC NORSRAM bank timing configuration using the function FMC_NORSRAM_Timing_Init()
(+) FMC NORSRAM bank extended timing configuration using the function
FMC_NORSRAM_Extended_Timing_Init()
(+) FMC NORSRAM bank enable/disable write operation using the functions
FMC_NORSRAM_WriteOperation_Enable()/FMC_NORSRAM_WriteOperation_Disable()
@endverbatim
* @{
*/
/** @defgroup HAL_FMC_NORSRAM_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FMC NORSRAM interface
(+) De-initialize the FMC NORSRAM interface
(+) Configure the FMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initialize the FMC_NORSRAM device according to the specified
* control parameters in the FMC_NORSRAM_InitTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Init: Pointer to NORSRAM Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_InitTypeDef* Init)
{
uint32_t tmpr = 0;
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_DEVICE(Device));
assert_param(IS_FMC_NORSRAM_BANK(Init->NSBank));
assert_param(IS_FMC_MUX(Init->DataAddressMux));
assert_param(IS_FMC_MEMORY(Init->MemoryType));
assert_param(IS_FMC_NORSRAM_MEMORY_WIDTH(Init->MemoryDataWidth));
assert_param(IS_FMC_BURSTMODE(Init->BurstAccessMode));
assert_param(IS_FMC_WAIT_POLARITY(Init->WaitSignalPolarity));
assert_param(IS_FMC_WRAP_MODE(Init->WrapMode));
assert_param(IS_FMC_WAIT_SIGNAL_ACTIVE(Init->WaitSignalActive));
assert_param(IS_FMC_WRITE_OPERATION(Init->WriteOperation));
assert_param(IS_FMC_WAITE_SIGNAL(Init->WaitSignal));
assert_param(IS_FMC_EXTENDED_MODE(Init->ExtendedMode));
assert_param(IS_FMC_ASYNWAIT(Init->AsynchronousWait));
assert_param(IS_FMC_WRITE_BURST(Init->WriteBurst));
assert_param(IS_FMC_CONTINOUS_CLOCK(Init->ContinuousClock));
/* Set NORSRAM device control parameters */
tmpr = (uint32_t)(Init->DataAddressMux |\
Init->MemoryType |\
Init->MemoryDataWidth |\
Init->BurstAccessMode |\
Init->WaitSignalPolarity |\
Init->WrapMode |\
Init->WaitSignalActive |\
Init->WriteOperation |\
Init->WaitSignal |\
Init->ExtendedMode |\
Init->AsynchronousWait |\
Init->WriteBurst |\
Init->ContinuousClock
);
if(Init->MemoryType == FMC_MEMORY_TYPE_NOR)
{
tmpr |= (uint32_t)FMC_NORSRAM_FLASH_ACCESS_ENABLE;
}
Device->BTCR[Init->NSBank] = tmpr;
/* Configure synchronous mode when Continuous clock is enabled for bank2..4 */
if((Init->ContinuousClock == FMC_CONTINUOUS_CLOCK_SYNC_ASYNC) && (Init->NSBank != FMC_NORSRAM_BANK1))
{
Init->BurstAccessMode = FMC_BURST_ACCESS_MODE_ENABLE;
Device->BTCR[FMC_NORSRAM_BANK1] |= (uint32_t)(Init->BurstAccessMode |\
Init->ContinuousClock);
}
return HAL_OK;
}
/**
* @brief DeInitialize the FMC_NORSRAM peripheral
* @param Device: Pointer to NORSRAM device instance
* @param ExDevice: Pointer to NORSRAM extended mode device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_DeInit(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_DEVICE(Device));
assert_param(IS_FMC_NORSRAM_EXTENDED_DEVICE(ExDevice));
assert_param(IS_FMC_NORSRAM_BANK(Bank));
/* Disable the FMC_NORSRAM device */
__FMC_NORSRAM_DISABLE(Device, Bank);
/* De-initialize the FMC_NORSRAM device */
/* FMC_NORSRAM_BANK1 */
if(Bank == FMC_NORSRAM_BANK1)
{
Device->BTCR[Bank] = 0x000030DB;
}
/* FMC_NORSRAM_BANK2, FMC_NORSRAM_BANK3 or FMC_NORSRAM_BANK4 */
else
{
Device->BTCR[Bank] = 0x000030D2;
}
Device->BTCR[Bank + 1] = 0x0FFFFFFF;
ExDevice->BWTR[Bank] = 0x0FFFFFFF;
return HAL_OK;
}
/**
* @brief Initialize the FMC_NORSRAM Timing according to the specified
* parameters in the FMC_NORSRAM_TimingTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Timing: Pointer to NORSRAM Timing structure
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_Timing_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmpr = 0;
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_DEVICE(Device));
assert_param(IS_FMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime));
assert_param(IS_FMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime));
assert_param(IS_FMC_DATASETUP_TIME(Timing->DataSetupTime));
assert_param(IS_FMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration));
assert_param(IS_FMC_CLK_DIV(Timing->CLKDivision));
assert_param(IS_FMC_DATA_LATENCY(Timing->DataLatency));
assert_param(IS_FMC_ACCESS_MODE(Timing->AccessMode));
assert_param(IS_FMC_NORSRAM_BANK(Bank));
/* Set FMC_NORSRAM device timing parameters */
tmpr = (uint32_t)(Timing->AddressSetupTime |\
((Timing->AddressHoldTime) << 4) |\
((Timing->DataSetupTime) << 8) |\
((Timing->BusTurnAroundDuration) << 16) |\
(((Timing->CLKDivision)-1) << 20) |\
(((Timing->DataLatency)-2) << 24) |\
(Timing->AccessMode)
);
Device->BTCR[Bank + 1] = tmpr;
/* Configure Clock division value (in NORSRAM bank 1) when continuous clock is enabled */
if(HAL_IS_BIT_SET(Device->BTCR[FMC_NORSRAM_BANK1], FMC_BCR1_CCLKEN))
{
tmpr = (uint32_t)(Device->BTCR[FMC_NORSRAM_BANK1 + 1] & ~(((uint32_t)0x0F) << 20));
tmpr |= (uint32_t)(((Timing->CLKDivision)-1) << 20);
Device->BTCR[FMC_NORSRAM_BANK1 + 1] = tmpr;
}
return HAL_OK;
}
/**
* @brief Initialize the FMC_NORSRAM Extended mode Timing according to the specified
* parameters in the FMC_NORSRAM_TimingTypeDef
* @param Device: Pointer to NORSRAM device instance
* @param Timing: Pointer to NORSRAM Timing structure
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_Extended_Timing_Init(FMC_NORSRAM_EXTENDED_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank, uint32_t ExtendedMode)
{
/* Check the parameters */
assert_param(IS_FMC_EXTENDED_MODE(ExtendedMode));
/* Set NORSRAM device timing register for write configuration, if extended mode is used */
if(ExtendedMode == FMC_EXTENDED_MODE_ENABLE)
{
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_EXTENDED_DEVICE(Device));
assert_param(IS_FMC_ADDRESS_SETUP_TIME(Timing->AddressSetupTime));
assert_param(IS_FMC_ADDRESS_HOLD_TIME(Timing->AddressHoldTime));
assert_param(IS_FMC_DATASETUP_TIME(Timing->DataSetupTime));
assert_param(IS_FMC_TURNAROUND_TIME(Timing->BusTurnAroundDuration));
assert_param(IS_FMC_CLK_DIV(Timing->CLKDivision));
assert_param(IS_FMC_DATA_LATENCY(Timing->DataLatency));
assert_param(IS_FMC_ACCESS_MODE(Timing->AccessMode));
assert_param(IS_FMC_NORSRAM_BANK(Bank));
Device->BWTR[Bank] = (uint32_t)(Timing->AddressSetupTime |\
((Timing->AddressHoldTime) << 4) |\
((Timing->DataSetupTime) << 8) |\
((Timing->BusTurnAroundDuration) << 16) |\
(((Timing->CLKDivision)-1) << 20) |\
(((Timing->DataLatency)-2) << 24) |\
(Timing->AccessMode));
}
else
{
Device->BWTR[Bank] = 0x0FFFFFFF;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup HAL_FMC_NORSRAM_Group3 Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### FMC_NORSRAM Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the FMC NORSRAM interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically FMC_NORSRAM write operation.
* @param Device: Pointer to NORSRAM device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Enable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_DEVICE(Device));
assert_param(IS_FMC_NORSRAM_BANK(Bank));
/* Enable write operation */
Device->BTCR[Bank] |= FMC_WRITE_OPERATION_ENABLE;
return HAL_OK;
}
/**
* @brief Disables dynamically FMC_NORSRAM write operation.
* @param Device: Pointer to NORSRAM device instance
* @param Bank: NORSRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Disable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NORSRAM_DEVICE(Device));
assert_param(IS_FMC_NORSRAM_BANK(Bank));
/* Disable write operation */
Device->BTCR[Bank] &= ~FMC_WRITE_OPERATION_ENABLE;
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
/** @defgroup FMC_PCCARD Controller functions
* @brief PCCARD Controller functions
*
@verbatim
==============================================================================
##### How to use NAND device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FMC NAND banks in order
to run the NAND external devices.
(+) FMC NAND bank reset using the function FMC_NAND_DeInit()
(+) FMC NAND bank control configuration using the function FMC_NAND_Init()
(+) FMC NAND bank common space timing configuration using the function
FMC_NAND_CommonSpace_Timing_Init()
(+) FMC NAND bank attribute space timing configuration using the function
FMC_NAND_AttributeSpace_Timing_Init()
(+) FMC NAND bank enable/disable ECC correction feature using the functions
FMC_NAND_ECC_Enable()/FMC_NAND_ECC_Disable()
(+) FMC NAND bank get ECC correction code using the function FMC_NAND_GetECC()
@endverbatim
* @{
*/
/** @defgroup HAL_FMC_NAND_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FMC NAND interface
(+) De-initialize the FMC NAND interface
(+) Configure the FMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initializes the FMC_NAND device according to the specified
* control parameters in the FMC_NAND_HandleTypeDef
* @param Device: Pointer to NAND device instance
* @param Init: Pointer to NAND Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_Init(FMC_NAND_TypeDef *Device, FMC_NAND_InitTypeDef *Init)
{
uint32_t tmppcr = 0;
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_NAND_BANK(Init->NandBank));
assert_param(IS_FMC_WAIT_FEATURE(Init->Waitfeature));
assert_param(IS_FMC_NAND_MEMORY_WIDTH(Init->MemoryDataWidth));
assert_param(IS_FMC_ECC_STATE(Init->EccComputation));
assert_param(IS_FMC_ECCPAGE_SIZE(Init->ECCPageSize));
assert_param(IS_FMC_TCLR_TIME(Init->TCLRSetupTime));
assert_param(IS_FMC_TAR_TIME(Init->TARSetupTime));
/* Set NAND device control parameters */
tmppcr = (uint32_t)(Init->Waitfeature |\
FMC_PCR_MEMORY_TYPE_NAND |\
Init->MemoryDataWidth |\
Init->EccComputation |\
Init->ECCPageSize |\
((Init->TCLRSetupTime) << 9) |\
((Init->TARSetupTime) << 13)
);
if(Init->NandBank == FMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PCR2 = tmppcr;
}
else
{
/* NAND bank 3 registers configuration */
Device->PCR3 = tmppcr;
}
return HAL_OK;
}
/**
* @brief Initializes the FMC_NAND Common space Timing according to the specified
* parameters in the FMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to NAND device instance
* @param Timing: Pointer to NAND timing structure
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_CommonSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmppmem = 0;
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime));
assert_param(IS_FMC_NAND_BANK(Bank));
/* Set FMC_NAND device timing parameters */
tmppmem = (uint32_t)(Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
((Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
if(Bank == FMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PMEM2 = tmppmem;
}
else
{
/* NAND bank 3 registers configuration */
Device->PMEM3 = tmppmem;
}
return HAL_OK;
}
/**
* @brief Initializes the FMC_NAND Attribute space Timing according to the specified
* parameters in the FMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to NAND device instance
* @param Timing: Pointer to NAND timing structure
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_AttributeSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmppatt = 0;
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime));
assert_param(IS_FMC_NAND_BANK(Bank));
/* Set FMC_NAND device timing parameters */
tmppatt = (uint32_t)(Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
((Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
if(Bank == FMC_NAND_BANK2)
{
/* NAND bank 2 registers configuration */
Device->PATT2 = tmppatt;
}
else
{
/* NAND bank 3 registers configuration */
Device->PATT3 = tmppatt;
}
return HAL_OK;
}
/**
* @brief DeInitializes the FMC_NAND device
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_DeInit(FMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_NAND_BANK(Bank));
/* Disable the NAND Bank */
__FMC_NAND_DISABLE(Device, Bank);
/* De-initialize the NAND Bank */
if(Bank == FMC_NAND_BANK2)
{
/* Set the FMC_NAND_BANK2 registers to their reset values */
Device->PCR2 = 0x00000018;
Device->SR2 = 0x00000040;
Device->PMEM2 = 0xFCFCFCFC;
Device->PATT2 = 0xFCFCFCFC;
}
/* FMC_Bank3_NAND */
else
{
/* Set the FMC_NAND_BANK3 registers to their reset values */
Device->PCR3 = 0x00000018;
Device->SR3 = 0x00000040;
Device->PMEM3 = 0xFCFCFCFC;
Device->PATT3 = 0xFCFCFCFC;
}
return HAL_OK;
}
/**
* @}
*/
/** @defgroup HAL_FMC_NAND_Group3 Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### FMC_NAND Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the FMC NAND interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically FMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_ECC_Enable(FMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_NAND_BANK(Bank));
/* Enable ECC feature */
if(Bank == FMC_NAND_BANK2)
{
Device->PCR2 |= FMC_PCR2_ECCEN;
}
else
{
Device->PCR3 |= FMC_PCR3_ECCEN;
}
return HAL_OK;
}
/**
* @brief Disables dynamically FMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param Bank: NAND bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_ECC_Disable(FMC_NAND_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_NAND_BANK(Bank));
/* Disable ECC feature */
if(Bank == FMC_NAND_BANK2)
{
Device->PCR2 &= ~FMC_PCR2_ECCEN;
}
else
{
Device->PCR3 &= ~FMC_PCR3_ECCEN;
}
return HAL_OK;
}
/**
* @brief Disables dynamically FMC_NAND ECC feature.
* @param Device: Pointer to NAND device instance
* @param ECCval: Pointer to ECC value
* @param Bank: NAND bank number
* @param Timeout: Timeout wait value
* @retval HAL status
*/
HAL_StatusTypeDef FMC_NAND_GetECC(FMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank, uint32_t Timeout)
{
uint32_t timeout = 0;
/* Check the parameters */
assert_param(IS_FMC_NAND_DEVICE(Device));
assert_param(IS_FMC_NAND_BANK(Bank));
timeout = HAL_GetTick() + Timeout;
/* Wait untill FIFO is empty */
while(__FMC_NAND_GET_FLAG(Device, Bank, FMC_FLAG_FEMPT))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
return HAL_TIMEOUT;
}
}
}
if(Bank == FMC_NAND_BANK2)
{
/* Get the ECCR2 register value */
*ECCval = (uint32_t)Device->ECCR2;
}
else
{
/* Get the ECCR3 register value */
*ECCval = (uint32_t)Device->ECCR3;
}
return HAL_OK;
}
/**
* @}
*/
/**
* @}
*/
/** @defgroup FMC_PCCARD Controller functions
* @brief PCCARD Controller functions
*
@verbatim
==============================================================================
##### How to use PCCARD device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FMC PCCARD bank in order
to run the PCCARD/compact flash external devices.
(+) FMC PCCARD bank reset using the function FMC_PCCARD_DeInit()
(+) FMC PCCARD bank control configuration using the function FMC_PCCARD_Init()
(+) FMC PCCARD bank common space timing configuration using the function
FMC_PCCARD_CommonSpace_Timing_Init()
(+) FMC PCCARD bank attribute space timing configuration using the function
FMC_PCCARD_AttributeSpace_Timing_Init()
(+) FMC PCCARD bank IO space timing configuration using the function
FMC_PCCARD_IOSpace_Timing_Init()
@endverbatim
* @{
*/
/** @defgroup HAL_FMC_PCCARD_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FMC PCCARD interface
(+) De-initialize the FMC PCCARD interface
(+) Configure the FMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initializes the FMC_PCCARD device according to the specified
* control parameters in the FMC_PCCARD_HandleTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Init: Pointer to PCCARD Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_PCCARD_Init(FMC_PCCARD_TypeDef *Device, FMC_PCCARD_InitTypeDef *Init)
{
/* Check the parameters */
assert_param(IS_FMC_PCCARD_DEVICE(Device));
assert_param(IS_FMC_WAIT_FEATURE(Init->Waitfeature));
assert_param(IS_FMC_TCLR_TIME(Init->TCLRSetupTime));
assert_param(IS_FMC_TAR_TIME(Init->TARSetupTime));
/* Set FMC_PCCARD device control parameters */
Device->PCR4 = (uint32_t)(Init->Waitfeature |\
FMC_NAND_PCC_MEM_BUS_WIDTH_16 |\
(Init->TCLRSetupTime << 9) |\
(Init->TARSetupTime << 13));
return HAL_OK;
}
/**
* @brief Initializes the FMC_PCCARD Common space Timing according to the specified
* parameters in the FMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_PCCARD_CommonSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FMC_PCCARD_DEVICE(Device));
assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set PCCARD timing parameters */
Device->PMEM4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief Initializes the FMC_PCCARD Attribute space Timing according to the specified
* parameters in the FMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_PCCARD_AttributeSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FMC_PCCARD_DEVICE(Device));
assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set PCCARD timing parameters */
Device->PATT4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief Initializes the FMC_PCCARD IO space Timing according to the specified
* parameters in the FMC_NAND_PCC_TimingTypeDef
* @param Device: Pointer to PCCARD device instance
* @param Timing: Pointer to PCCARD timing structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_PCCARD_IOSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing)
{
/* Check the parameters */
assert_param(IS_FMC_PCCARD_DEVICE(Device));
assert_param(IS_FMC_SETUP_TIME(Timing->SetupTime));
assert_param(IS_FMC_WAIT_TIME(Timing->WaitSetupTime));
assert_param(IS_FMC_HOLD_TIME(Timing->HoldSetupTime));
assert_param(IS_FMC_HIZ_TIME(Timing->HiZSetupTime));
/* Set FMC_PCCARD device timing parameters */
Device->PIO4 = (uint32_t)((Timing->SetupTime |\
((Timing->WaitSetupTime) << 8) |\
(Timing->HoldSetupTime) << 16) |\
((Timing->HiZSetupTime) << 24)
);
return HAL_OK;
}
/**
* @brief DeInitializes the FMC_PCCARD device
* @param Device: Pointer to PCCARD device instance
* @retval HAL status
*/
HAL_StatusTypeDef FMC_PCCARD_DeInit(FMC_PCCARD_TypeDef *Device)
{
/* Check the parameters */
assert_param(IS_FMC_PCCARD_DEVICE(Device));
/* Disable the FMC_PCCARD device */
__FMC_PCCARD_DISABLE(Device);
/* De-initialize the FMC_PCCARD device */
Device->PCR4 = 0x00000018;
Device->SR4 = 0x00000000;
Device->PMEM4 = 0xFCFCFCFC;
Device->PATT4 = 0xFCFCFCFC;
Device->PIO4 = 0xFCFCFCFC;
return HAL_OK;
}
/**
* @}
*/
/** @defgroup FMC_SDRAM Controller functions
* @brief SDRAM Controller functions
*
@verbatim
==============================================================================
##### How to use SDRAM device driver #####
==============================================================================
[..]
This driver contains a set of APIs to interface with the FMC SDRAM banks in order
to run the SDRAM external devices.
(+) FMC SDRAM bank reset using the function FMC_SDRAM_DeInit()
(+) FMC SDRAM bank control configuration using the function FMC_SDRAM_Init()
(+) FMC SDRAM bank timing configuration using the function FMC_SDRAM_Timing_Init()
(+) FMC SDRAM bank enable/disable write operation using the functions
FMC_SDRAM_WriteOperation_Enable()/FMC_SDRAM_WriteOperation_Disable()
(+) FMC SDRAM bank send command using the function FMC_SDRAM_SendCommand()
@endverbatim
* @{
*/
/** @defgroup HAL_FMC_SDRAM_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
==============================================================================
##### Initialization and de_initialization functions #####
==============================================================================
[..]
This section provides functions allowing to:
(+) Initialize and configure the FMC SDRAM interface
(+) De-initialize the FMC SDRAM interface
(+) Configure the FMC clock and associated GPIOs
@endverbatim
* @{
*/
/**
* @brief Initializes the FMC_SDRAM device according to the specified
* control parameters in the FMC_SDRAM_InitTypeDef
* @param Device: Pointer to SDRAM device instance
* @param Init: Pointer to SDRAM Initialization structure
* @retval HAL status
*/
HAL_StatusTypeDef FMC_SDRAM_Init(FMC_SDRAM_TypeDef *Device, FMC_SDRAM_InitTypeDef *Init)
{
uint32_t tmpr1 = 0;
uint32_t tmpr2 = 0;
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_SDRAM_BANK(Init->SDBank));
assert_param(IS_FMC_COLUMNBITS_NUMBER(Init->ColumnBitsNumber));
assert_param(IS_FMC_ROWBITS_NUMBER(Init->RowBitsNumber));
assert_param(IS_FMC_SDMEMORY_WIDTH(Init->MemoryDataWidth));
assert_param(IS_FMC_INTERNALBANK_NUMBER(Init->InternalBankNumber));
assert_param(IS_FMC_CAS_LATENCY(Init->CASLatency));
assert_param(IS_FMC_WRITE_PROTECTION(Init->WriteProtection));
assert_param(IS_FMC_SDCLOCK_PERIOD(Init->SDClockPeriod));
assert_param(IS_FMC_READ_BURST(Init->ReadBurst));
assert_param(IS_FMC_READPIPE_DELAY(Init->ReadPipeDelay));
/* Set SDRAM bank configuration parameters */
if (Init->SDBank != FMC_SDRAM_BANK2)
{
Device->SDCR[FMC_SDRAM_BANK1] = (uint32_t)(Init->ColumnBitsNumber |\
Init->RowBitsNumber |\
Init->MemoryDataWidth |\
Init->InternalBankNumber |\
Init->CASLatency |\
Init->WriteProtection |\
Init->SDClockPeriod |\
Init->ReadBurst |\
Init->ReadPipeDelay
);
}
else /* FMC_Bank2_SDRAM */
{
tmpr1 = (uint32_t)(Init->SDClockPeriod |\
Init->ReadBurst |\
Init->ReadPipeDelay
);
tmpr2 = (uint32_t)(Init->ColumnBitsNumber |\
Init->RowBitsNumber |\
Init->MemoryDataWidth |\
Init->InternalBankNumber |\
Init->CASLatency |\
Init->WriteProtection
);
Device->SDCR[FMC_SDRAM_BANK1] = tmpr1;
Device->SDCR[FMC_SDRAM_BANK2] = tmpr2;
}
return HAL_OK;
}
/**
* @brief Initializes the FMC_SDRAM device timing according to the specified
* parameters in the FMC_SDRAM_TimingTypeDef
* @param Device: Pointer to SDRAM device instance
* @param Timing: Pointer to SDRAM Timing structure
* @param Bank: SDRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_SDRAM_Timing_Init(FMC_SDRAM_TypeDef *Device, FMC_SDRAM_TimingTypeDef *Timing, uint32_t Bank)
{
uint32_t tmpr1 = 0;
uint32_t tmpr2 = 0;
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_LOADTOACTIVE_DELAY(Timing->LoadToActiveDelay));
assert_param(IS_FMC_EXITSELFREFRESH_DELAY(Timing->ExitSelfRefreshDelay));
assert_param(IS_FMC_SELFREFRESH_TIME(Timing->SelfRefreshTime));
assert_param(IS_FMC_ROWCYCLE_DELAY(Timing->RowCycleDelay));
assert_param(IS_FMC_WRITE_RECOVERY_TIME(Timing->WriteRecoveryTime));
assert_param(IS_FMC_RP_DELAY(Timing->RPDelay));
assert_param(IS_FMC_RCD_DELAY(Timing->RCDDelay));
assert_param(IS_FMC_SDRAM_BANK(Bank));
/* Set SDRAM device timing parameters */
if (Bank != FMC_SDRAM_BANK2)
{
Device->SDTR[FMC_SDRAM_BANK1] = (uint32_t)(((Timing->LoadToActiveDelay)-1) |\
(((Timing->ExitSelfRefreshDelay)-1) << 4) |\
(((Timing->SelfRefreshTime)-1) << 8) |\
(((Timing->RowCycleDelay)-1) << 12) |\
(((Timing->WriteRecoveryTime)-1) <<16) |\
(((Timing->RPDelay)-1) << 20) |\
(((Timing->RCDDelay)-1) << 24)
);
}
else /* FMC_Bank2_SDRAM */
{
tmpr1 = (uint32_t)(((Timing->LoadToActiveDelay)-1) |\
(((Timing->ExitSelfRefreshDelay)-1) << 4) |\
(((Timing->SelfRefreshTime)-1) << 8) |\
(((Timing->WriteRecoveryTime)-1) <<16) |\
(((Timing->RCDDelay)-1) << 24)
);
tmpr2 = (uint32_t)((((Timing->RowCycleDelay)-1) << 12) |\
(((Timing->RPDelay)-1) << 20)
);
Device->SDTR[FMC_SDRAM_BANK2] = tmpr1;
Device->SDTR[FMC_SDRAM_BANK1] = tmpr2;
}
return HAL_OK;
}
/**
* @brief DeInitializes the FMC_SDRAM peripheral
* @param Device: Pointer to SDRAM device instance
* @retval HAL status
*/
HAL_StatusTypeDef FMC_SDRAM_DeInit(FMC_SDRAM_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_SDRAM_BANK(Bank));
/* De-initialize the SDRAM device */
Device->SDCR[Bank] = 0x000002D0;
Device->SDTR[Bank] = 0x0FFFFFFF;
Device->SDCMR = 0x00000000;
Device->SDRTR = 0x00000000;
Device->SDSR = 0x00000000;
return HAL_OK;
}
/**
* @}
*/
/** @defgroup HAL_FMC_SDRAM_Group3 Control functions
* @brief management functions
*
@verbatim
==============================================================================
##### FMC_SDRAM Control functions #####
==============================================================================
[..]
This subsection provides a set of functions allowing to control dynamically
the FMC SDRAM interface.
@endverbatim
* @{
*/
/**
* @brief Enables dynamically FMC_SDRAM write protection.
* @param Device: Pointer to SDRAM device instance
* @param Bank: SDRAM bank number
* @retval HAL status
*/
HAL_StatusTypeDef FMC_SDRAM_WriteProtection_Enable(FMC_SDRAM_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_SDRAM_BANK(Bank));
/* Enable write protection */
Device->SDCR[Bank] |= FMC_SDRAM_WRITE_PROTECTION_ENABLE;
return HAL_OK;
}
/**
* @brief Disables dynamically FMC_SDRAM write protection.
* @param hsdram: FMC_SDRAM handle
* @retval HAL status
*/
HAL_StatusTypeDef FMC_SDRAM_WriteProtection_Disable(FMC_SDRAM_TypeDef *Device, uint32_t Bank)
{
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_SDRAM_BANK(Bank));
/* Disable write protection */
Device->SDCR[Bank] &= ~FMC_SDRAM_WRITE_PROTECTION_ENABLE;
return HAL_OK;
}
/**
* @brief Send Command to the FMC SDRAM bank
* @param Device: Pointer to SDRAM device instance
* @param Command: Pointer to SDRAM command structure
* @param Timing: Pointer to SDRAM Timing structure
* @param Timeout: Timeout wait value
* @retval HAL state
*/
HAL_StatusTypeDef FMC_SDRAM_SendCommand(FMC_SDRAM_TypeDef *Device, FMC_SDRAM_CommandTypeDef *Command, uint32_t Timeout)
{
__IO uint32_t tmpr = 0;
uint32_t timeout = 0;
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_COMMAND_MODE(Command->CommandMode));
assert_param(IS_FMC_COMMAND_TARGET(Command->CommandTarget));
assert_param(IS_FMC_AUTOREFRESH_NUMBER(Command->AutoRefreshNumber));
assert_param(IS_FMC_MODE_REGISTER(Command->ModeRegisterDefinition));
/* Set command register */
tmpr = (uint32_t)((Command->CommandMode) |\
(Command->CommandTarget) |\
(((Command->AutoRefreshNumber)-1) << 5) |\
((Command->ModeRegisterDefinition) << 9)
);
Device->SDCMR = tmpr;
timeout = HAL_GetTick() + Timeout;
/* wait until command is send */
while(HAL_IS_BIT_SET(Device->SDSR, FMC_SDSR_BUSY))
{
/* Check for the Timeout */
if(Timeout != HAL_MAX_DELAY)
{
if(HAL_GetTick() >= timeout)
{
return HAL_TIMEOUT;
}
}
return HAL_ERROR;
}
return HAL_OK;
}
/**
* @brief Program the SDRAM Memory Refresh rate.
* @param Device: Pointer to SDRAM device instance
* @param RefreshRate: The SDRAM refresh rate value.
* @retval HAL state
*/
HAL_StatusTypeDef FMC_SDRAM_ProgramRefreshRate(FMC_SDRAM_TypeDef *Device, uint32_t RefreshRate)
{
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_REFRESH_RATE(RefreshRate));
/* Set the refresh rate in command register */
Device->SDRTR |= (RefreshRate<<1);
return HAL_OK;
}
/**
* @brief Set the Number of consecutive SDRAM Memory auto Refresh commands.
* @param Device: Pointer to SDRAM device instance
* @param AutoRefreshNumber: Specifies the auto Refresh number.
* @retval None
*/
HAL_StatusTypeDef FMC_SDRAM_SetAutoRefreshNumber(FMC_SDRAM_TypeDef *Device, uint32_t AutoRefreshNumber)
{
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_AUTOREFRESH_NUMBER(AutoRefreshNumber));
/* Set the Auto-refresh number in command register */
Device->SDCMR |= (AutoRefreshNumber << 5);
return HAL_OK;
}
/**
* @brief Returns the indicated FMC SDRAM bank mode status.
* @param Device: Pointer to SDRAM device instance
* @param Bank: Defines the FMC SDRAM bank. This parameter can be
* FMC_Bank1_SDRAM or FMC_Bank2_SDRAM.
* @retval The FMC SDRAM bank mode status, could be on of the following values:
* FMC_SDRAM_NORMAL_MODE, FMC_SDRAM_SELF_REFRESH_MODE or
* FMC_SDRAM_POWER_DOWN_MODE.
*/
uint32_t FMC_SDRAM_GetModeStatus(FMC_SDRAM_TypeDef *Device, uint32_t Bank)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_FMC_SDRAM_DEVICE(Device));
assert_param(IS_FMC_SDRAM_BANK(Bank));
/* Get the corresponding bank mode */
if(Bank == FMC_SDRAM_BANK1)
{
tmpreg = (uint32_t)(Device->SDSR & FMC_SDSR_MODES1);
}
else
{
tmpreg = ((uint32_t)(Device->SDSR & FMC_SDSR_MODES2) >> 2);
}
/* Return the mode status */
return tmpreg;
}
/**
* @}
*/
/**
* @}
*/
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#endif /* HAL_FMC_MODULE_ENABLED */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/