ref: a10d303e7c2d5f961c6b7ad5421cef5daf307fea
dir: /demos/stm32f429_disco/stm/usb_user/usbd_conf.h/
/**
******************************************************************************
* @file usbd_conf.h
* @author MCD Application Team
* @version V1.0.1
* @date 11-November-2013
* @brief Main program body
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __USBD_CONF__H__
#define __USBD_CONF__H__
/* Includes ------------------------------------------------------------------*/
/** @addtogroup STM32_USB_OTG_DEVICE_LIBRARY
* @{
*/
/** @defgroup USBD_CONF
* @brief This file is the device library configuration file
* @{
*/
/** @defgroup USBD_CONF_Exported_Defines
* @{
*/
#define USBD_CFG_MAX_NUM 1
#define USBD_ITF_MAX_NUM 1
#define USB_MAX_STR_DESC_SIZ 64
/* Class Layer Parameter MSC */
#define MSC_IN_EP 0x81
#define MSC_OUT_EP 0x01
#ifdef USE_USB_OTG_HS
#ifdef USE_ULPI_PHY
#define MSC_MAX_PACKET 512
#else
#define MSC_MAX_PACKET 64
#endif
#else /*USE_USB_OTG_FS*/
#define MSC_MAX_PACKET 64
#endif
#define MSC_MEDIA_PACKET 4096
/* Class Layer Parameter HID */
#define HID_IN_EP 0x81
#define HID_OUT_EP 0x01
#define HID_IN_PACKET 4
#define HID_OUT_PACKET 4
/* Class Layer Parameter HID */
#ifndef EXTERNAL_CRYSTAL_25MHz
#define USBD_AUDIO_FREQ 48000 /* Audio frequency in Hz. */
/*
It is advised to set standard frequencies >= 24KHz to get best quality
except for STM32F10 devices, when the HSE value is 25MHz, it is advised to
set audio frequencies reachable with this HSE value (refer to RM0008 for
more details). ie. it is advised to set 16KHz value in this case.
Note that maximum allowed audio frequency is 96KHz (this limitation is
due to the codec used on the Evaluation board. The STM32 I2S cell allows
to reach 192KHz frequency).
@note
When modifying this value, make sure that the I2S PLL configuration allows
to get minimum error on audio frequency. This configuration is set in file
system_stm32f2xx.c or system_stm32f10x.c.*/
#else
#define USBD_AUDIO_FREQ 16000 /* Audio frequency in Hz for STM32F10x devices family when 25MHz HSE value
is used. */
#endif /* EXTERNAL_CRYSTAL_25MHz */
#define DEFAULT_VOLUME 65 /* Default volume in % (Mute=0%, Max = 100%) in Logarithmic values.
To get accurate volume variations, it is possible to use a logarithmic
coversion table to convert from percentage to logarithmic law.
In order to keep this example code simple, this conversion is not used. */
/* Use this section to modify the number of supported interfaces and configurations.
Note that if you modify these parameters, you have to modify the descriptors
accordingly in usbd_audio_core.c file */
#define AUDIO_TOTAL_IF_NUM 0x02
#define AUDIO_OUT_EP 0x01
#define AUDIO_IN_EP 0x82
/**
* @}
*/
/** @defgroup USB_CONF_Exported_TypesDefinitions
* @{
*/
/**
* @}
*/
/** @defgroup USB_CONF_Exported_Macros
* @{
*/
/**
* @}
*/
/** @defgroup USB_CONF_Exported_Variables
* @{
*/
/**
* @}
*/
/** @defgroup USB_CONF_Exported_FunctionsPrototype
* @{
*/
/**
* @}
*/
#endif //__USBD_CONF__H__
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/