ref: cbf74d6c41613815366711a6a5322033c7c0ccc1
dir: /demos/stm32f429_disco/stm/stm32f4_spl/inc/stm32f4xx_sdio.h/
/**
******************************************************************************
* @file stm32f4xx_sdio.h
* @author MCD Application Team
* @version V1.3.0
* @date 08-November-2013
* @brief This file contains all the functions prototypes for the SDIO firmware
* library.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F4xx_SDIO_H
#define __STM32F4xx_SDIO_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx.h"
/** @addtogroup STM32F4xx_StdPeriph_Driver
* @{
*/
/** @addtogroup SDIO
* @{
*/
/* Exported types ------------------------------------------------------------*/
typedef struct
{
uint32_t SDIO_ClockEdge; /*!< Specifies the clock transition on which the bit capture is made.
This parameter can be a value of @ref SDIO_Clock_Edge */
uint32_t SDIO_ClockBypass; /*!< Specifies whether the SDIO Clock divider bypass is
enabled or disabled.
This parameter can be a value of @ref SDIO_Clock_Bypass */
uint32_t SDIO_ClockPowerSave; /*!< Specifies whether SDIO Clock output is enabled or
disabled when the bus is idle.
This parameter can be a value of @ref SDIO_Clock_Power_Save */
uint32_t SDIO_BusWide; /*!< Specifies the SDIO bus width.
This parameter can be a value of @ref SDIO_Bus_Wide */
uint32_t SDIO_HardwareFlowControl; /*!< Specifies whether the SDIO hardware flow control is enabled or disabled.
This parameter can be a value of @ref SDIO_Hardware_Flow_Control */
uint8_t SDIO_ClockDiv; /*!< Specifies the clock frequency of the SDIO controller.
This parameter can be a value between 0x00 and 0xFF. */
} SDIO_InitTypeDef;
typedef struct
{
uint32_t SDIO_Argument; /*!< Specifies the SDIO command argument which is sent
to a card as part of a command message. If a command
contains an argument, it must be loaded into this register
before writing the command to the command register */
uint32_t SDIO_CmdIndex; /*!< Specifies the SDIO command index. It must be lower than 0x40. */
uint32_t SDIO_Response; /*!< Specifies the SDIO response type.
This parameter can be a value of @ref SDIO_Response_Type */
uint32_t SDIO_Wait; /*!< Specifies whether SDIO wait for interrupt request is enabled or disabled.
This parameter can be a value of @ref SDIO_Wait_Interrupt_State */
uint32_t SDIO_CPSM; /*!< Specifies whether SDIO Command path state machine (CPSM)
is enabled or disabled.
This parameter can be a value of @ref SDIO_CPSM_State */
} SDIO_CmdInitTypeDef;
typedef struct
{
uint32_t SDIO_DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */
uint32_t SDIO_DataLength; /*!< Specifies the number of data bytes to be transferred. */
uint32_t SDIO_DataBlockSize; /*!< Specifies the data block size for block transfer.
This parameter can be a value of @ref SDIO_Data_Block_Size */
uint32_t SDIO_TransferDir; /*!< Specifies the data transfer direction, whether the transfer
is a read or write.
This parameter can be a value of @ref SDIO_Transfer_Direction */
uint32_t SDIO_TransferMode; /*!< Specifies whether data transfer is in stream or block mode.
This parameter can be a value of @ref SDIO_Transfer_Type */
uint32_t SDIO_DPSM; /*!< Specifies whether SDIO Data path state machine (DPSM)
is enabled or disabled.
This parameter can be a value of @ref SDIO_DPSM_State */
} SDIO_DataInitTypeDef;
/* Exported constants --------------------------------------------------------*/
/** @defgroup SDIO_Exported_Constants
* @{
*/
/** @defgroup SDIO_Clock_Edge
* @{
*/
#define SDIO_ClockEdge_Rising ((uint32_t)0x00000000)
#define SDIO_ClockEdge_Falling ((uint32_t)0x00002000)
#define IS_SDIO_CLOCK_EDGE(EDGE) (((EDGE) == SDIO_ClockEdge_Rising) || \
((EDGE) == SDIO_ClockEdge_Falling))
/**
* @}
*/
/** @defgroup SDIO_Clock_Bypass
* @{
*/
#define SDIO_ClockBypass_Disable ((uint32_t)0x00000000)
#define SDIO_ClockBypass_Enable ((uint32_t)0x00000400)
#define IS_SDIO_CLOCK_BYPASS(BYPASS) (((BYPASS) == SDIO_ClockBypass_Disable) || \
((BYPASS) == SDIO_ClockBypass_Enable))
/**
* @}
*/
/** @defgroup SDIO_Clock_Power_Save
* @{
*/
#define SDIO_ClockPowerSave_Disable ((uint32_t)0x00000000)
#define SDIO_ClockPowerSave_Enable ((uint32_t)0x00000200)
#define IS_SDIO_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDIO_ClockPowerSave_Disable) || \
((SAVE) == SDIO_ClockPowerSave_Enable))
/**
* @}
*/
/** @defgroup SDIO_Bus_Wide
* @{
*/
#define SDIO_BusWide_1b ((uint32_t)0x00000000)
#define SDIO_BusWide_4b ((uint32_t)0x00000800)
#define SDIO_BusWide_8b ((uint32_t)0x00001000)
#define IS_SDIO_BUS_WIDE(WIDE) (((WIDE) == SDIO_BusWide_1b) || ((WIDE) == SDIO_BusWide_4b) || \
((WIDE) == SDIO_BusWide_8b))
/**
* @}
*/
/** @defgroup SDIO_Hardware_Flow_Control
* @{
*/
#define SDIO_HardwareFlowControl_Disable ((uint32_t)0x00000000)
#define SDIO_HardwareFlowControl_Enable ((uint32_t)0x00004000)
#define IS_SDIO_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDIO_HardwareFlowControl_Disable) || \
((CONTROL) == SDIO_HardwareFlowControl_Enable))
/**
* @}
*/
/** @defgroup SDIO_Power_State
* @{
*/
#define SDIO_PowerState_OFF ((uint32_t)0x00000000)
#define SDIO_PowerState_ON ((uint32_t)0x00000003)
#define IS_SDIO_POWER_STATE(STATE) (((STATE) == SDIO_PowerState_OFF) || ((STATE) == SDIO_PowerState_ON))
/**
* @}
*/
/** @defgroup SDIO_Interrupt_sources
* @{
*/
#define SDIO_IT_CCRCFAIL ((uint32_t)0x00000001)
#define SDIO_IT_DCRCFAIL ((uint32_t)0x00000002)
#define SDIO_IT_CTIMEOUT ((uint32_t)0x00000004)
#define SDIO_IT_DTIMEOUT ((uint32_t)0x00000008)
#define SDIO_IT_TXUNDERR ((uint32_t)0x00000010)
#define SDIO_IT_RXOVERR ((uint32_t)0x00000020)
#define SDIO_IT_CMDREND ((uint32_t)0x00000040)
#define SDIO_IT_CMDSENT ((uint32_t)0x00000080)
#define SDIO_IT_DATAEND ((uint32_t)0x00000100)
#define SDIO_IT_STBITERR ((uint32_t)0x00000200)
#define SDIO_IT_DBCKEND ((uint32_t)0x00000400)
#define SDIO_IT_CMDACT ((uint32_t)0x00000800)
#define SDIO_IT_TXACT ((uint32_t)0x00001000)
#define SDIO_IT_RXACT ((uint32_t)0x00002000)
#define SDIO_IT_TXFIFOHE ((uint32_t)0x00004000)
#define SDIO_IT_RXFIFOHF ((uint32_t)0x00008000)
#define SDIO_IT_TXFIFOF ((uint32_t)0x00010000)
#define SDIO_IT_RXFIFOF ((uint32_t)0x00020000)
#define SDIO_IT_TXFIFOE ((uint32_t)0x00040000)
#define SDIO_IT_RXFIFOE ((uint32_t)0x00080000)
#define SDIO_IT_TXDAVL ((uint32_t)0x00100000)
#define SDIO_IT_RXDAVL ((uint32_t)0x00200000)
#define SDIO_IT_SDIOIT ((uint32_t)0x00400000)
#define SDIO_IT_CEATAEND ((uint32_t)0x00800000)
#define IS_SDIO_IT(IT) ((((IT) & (uint32_t)0xFF000000) == 0x00) && ((IT) != (uint32_t)0x00))
/**
* @}
*/
/** @defgroup SDIO_Command_Index
* @{
*/
#define IS_SDIO_CMD_INDEX(INDEX) ((INDEX) < 0x40)
/**
* @}
*/
/** @defgroup SDIO_Response_Type
* @{
*/
#define SDIO_Response_No ((uint32_t)0x00000000)
#define SDIO_Response_Short ((uint32_t)0x00000040)
#define SDIO_Response_Long ((uint32_t)0x000000C0)
#define IS_SDIO_RESPONSE(RESPONSE) (((RESPONSE) == SDIO_Response_No) || \
((RESPONSE) == SDIO_Response_Short) || \
((RESPONSE) == SDIO_Response_Long))
/**
* @}
*/
/** @defgroup SDIO_Wait_Interrupt_State
* @{
*/
#define SDIO_Wait_No ((uint32_t)0x00000000) /*!< SDIO No Wait, TimeOut is enabled */
#define SDIO_Wait_IT ((uint32_t)0x00000100) /*!< SDIO Wait Interrupt Request */
#define SDIO_Wait_Pend ((uint32_t)0x00000200) /*!< SDIO Wait End of transfer */
#define IS_SDIO_WAIT(WAIT) (((WAIT) == SDIO_Wait_No) || ((WAIT) == SDIO_Wait_IT) || \
((WAIT) == SDIO_Wait_Pend))
/**
* @}
*/
/** @defgroup SDIO_CPSM_State
* @{
*/
#define SDIO_CPSM_Disable ((uint32_t)0x00000000)
#define SDIO_CPSM_Enable ((uint32_t)0x00000400)
#define IS_SDIO_CPSM(CPSM) (((CPSM) == SDIO_CPSM_Enable) || ((CPSM) == SDIO_CPSM_Disable))
/**
* @}
*/
/** @defgroup SDIO_Response_Registers
* @{
*/
#define SDIO_RESP1 ((uint32_t)0x00000000)
#define SDIO_RESP2 ((uint32_t)0x00000004)
#define SDIO_RESP3 ((uint32_t)0x00000008)
#define SDIO_RESP4 ((uint32_t)0x0000000C)
#define IS_SDIO_RESP(RESP) (((RESP) == SDIO_RESP1) || ((RESP) == SDIO_RESP2) || \
((RESP) == SDIO_RESP3) || ((RESP) == SDIO_RESP4))
/**
* @}
*/
/** @defgroup SDIO_Data_Length
* @{
*/
#define IS_SDIO_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFF)
/**
* @}
*/
/** @defgroup SDIO_Data_Block_Size
* @{
*/
#define SDIO_DataBlockSize_1b ((uint32_t)0x00000000)
#define SDIO_DataBlockSize_2b ((uint32_t)0x00000010)
#define SDIO_DataBlockSize_4b ((uint32_t)0x00000020)
#define SDIO_DataBlockSize_8b ((uint32_t)0x00000030)
#define SDIO_DataBlockSize_16b ((uint32_t)0x00000040)
#define SDIO_DataBlockSize_32b ((uint32_t)0x00000050)
#define SDIO_DataBlockSize_64b ((uint32_t)0x00000060)
#define SDIO_DataBlockSize_128b ((uint32_t)0x00000070)
#define SDIO_DataBlockSize_256b ((uint32_t)0x00000080)
#define SDIO_DataBlockSize_512b ((uint32_t)0x00000090)
#define SDIO_DataBlockSize_1024b ((uint32_t)0x000000A0)
#define SDIO_DataBlockSize_2048b ((uint32_t)0x000000B0)
#define SDIO_DataBlockSize_4096b ((uint32_t)0x000000C0)
#define SDIO_DataBlockSize_8192b ((uint32_t)0x000000D0)
#define SDIO_DataBlockSize_16384b ((uint32_t)0x000000E0)
#define IS_SDIO_BLOCK_SIZE(SIZE) (((SIZE) == SDIO_DataBlockSize_1b) || \
((SIZE) == SDIO_DataBlockSize_2b) || \
((SIZE) == SDIO_DataBlockSize_4b) || \
((SIZE) == SDIO_DataBlockSize_8b) || \
((SIZE) == SDIO_DataBlockSize_16b) || \
((SIZE) == SDIO_DataBlockSize_32b) || \
((SIZE) == SDIO_DataBlockSize_64b) || \
((SIZE) == SDIO_DataBlockSize_128b) || \
((SIZE) == SDIO_DataBlockSize_256b) || \
((SIZE) == SDIO_DataBlockSize_512b) || \
((SIZE) == SDIO_DataBlockSize_1024b) || \
((SIZE) == SDIO_DataBlockSize_2048b) || \
((SIZE) == SDIO_DataBlockSize_4096b) || \
((SIZE) == SDIO_DataBlockSize_8192b) || \
((SIZE) == SDIO_DataBlockSize_16384b))
/**
* @}
*/
/** @defgroup SDIO_Transfer_Direction
* @{
*/
#define SDIO_TransferDir_ToCard ((uint32_t)0x00000000)
#define SDIO_TransferDir_ToSDIO ((uint32_t)0x00000002)
#define IS_SDIO_TRANSFER_DIR(DIR) (((DIR) == SDIO_TransferDir_ToCard) || \
((DIR) == SDIO_TransferDir_ToSDIO))
/**
* @}
*/
/** @defgroup SDIO_Transfer_Type
* @{
*/
#define SDIO_TransferMode_Block ((uint32_t)0x00000000)
#define SDIO_TransferMode_Stream ((uint32_t)0x00000004)
#define IS_SDIO_TRANSFER_MODE(MODE) (((MODE) == SDIO_TransferMode_Stream) || \
((MODE) == SDIO_TransferMode_Block))
/**
* @}
*/
/** @defgroup SDIO_DPSM_State
* @{
*/
#define SDIO_DPSM_Disable ((uint32_t)0x00000000)
#define SDIO_DPSM_Enable ((uint32_t)0x00000001)
#define IS_SDIO_DPSM(DPSM) (((DPSM) == SDIO_DPSM_Enable) || ((DPSM) == SDIO_DPSM_Disable))
/**
* @}
*/
/** @defgroup SDIO_Flags
* @{
*/
#define SDIO_FLAG_CCRCFAIL ((uint32_t)0x00000001)
#define SDIO_FLAG_DCRCFAIL ((uint32_t)0x00000002)
#define SDIO_FLAG_CTIMEOUT ((uint32_t)0x00000004)
#define SDIO_FLAG_DTIMEOUT ((uint32_t)0x00000008)
#define SDIO_FLAG_TXUNDERR ((uint32_t)0x00000010)
#define SDIO_FLAG_RXOVERR ((uint32_t)0x00000020)
#define SDIO_FLAG_CMDREND ((uint32_t)0x00000040)
#define SDIO_FLAG_CMDSENT ((uint32_t)0x00000080)
#define SDIO_FLAG_DATAEND ((uint32_t)0x00000100)
#define SDIO_FLAG_STBITERR ((uint32_t)0x00000200)
#define SDIO_FLAG_DBCKEND ((uint32_t)0x00000400)
#define SDIO_FLAG_CMDACT ((uint32_t)0x00000800)
#define SDIO_FLAG_TXACT ((uint32_t)0x00001000)
#define SDIO_FLAG_RXACT ((uint32_t)0x00002000)
#define SDIO_FLAG_TXFIFOHE ((uint32_t)0x00004000)
#define SDIO_FLAG_RXFIFOHF ((uint32_t)0x00008000)
#define SDIO_FLAG_TXFIFOF ((uint32_t)0x00010000)
#define SDIO_FLAG_RXFIFOF ((uint32_t)0x00020000)
#define SDIO_FLAG_TXFIFOE ((uint32_t)0x00040000)
#define SDIO_FLAG_RXFIFOE ((uint32_t)0x00080000)
#define SDIO_FLAG_TXDAVL ((uint32_t)0x00100000)
#define SDIO_FLAG_RXDAVL ((uint32_t)0x00200000)
#define SDIO_FLAG_SDIOIT ((uint32_t)0x00400000)
#define SDIO_FLAG_CEATAEND ((uint32_t)0x00800000)
#define IS_SDIO_FLAG(FLAG) (((FLAG) == SDIO_FLAG_CCRCFAIL) || \
((FLAG) == SDIO_FLAG_DCRCFAIL) || \
((FLAG) == SDIO_FLAG_CTIMEOUT) || \
((FLAG) == SDIO_FLAG_DTIMEOUT) || \
((FLAG) == SDIO_FLAG_TXUNDERR) || \
((FLAG) == SDIO_FLAG_RXOVERR) || \
((FLAG) == SDIO_FLAG_CMDREND) || \
((FLAG) == SDIO_FLAG_CMDSENT) || \
((FLAG) == SDIO_FLAG_DATAEND) || \
((FLAG) == SDIO_FLAG_STBITERR) || \
((FLAG) == SDIO_FLAG_DBCKEND) || \
((FLAG) == SDIO_FLAG_CMDACT) || \
((FLAG) == SDIO_FLAG_TXACT) || \
((FLAG) == SDIO_FLAG_RXACT) || \
((FLAG) == SDIO_FLAG_TXFIFOHE) || \
((FLAG) == SDIO_FLAG_RXFIFOHF) || \
((FLAG) == SDIO_FLAG_TXFIFOF) || \
((FLAG) == SDIO_FLAG_RXFIFOF) || \
((FLAG) == SDIO_FLAG_TXFIFOE) || \
((FLAG) == SDIO_FLAG_RXFIFOE) || \
((FLAG) == SDIO_FLAG_TXDAVL) || \
((FLAG) == SDIO_FLAG_RXDAVL) || \
((FLAG) == SDIO_FLAG_SDIOIT) || \
((FLAG) == SDIO_FLAG_CEATAEND))
#define IS_SDIO_CLEAR_FLAG(FLAG) ((((FLAG) & (uint32_t)0xFF3FF800) == 0x00) && ((FLAG) != (uint32_t)0x00))
#define IS_SDIO_GET_IT(IT) (((IT) == SDIO_IT_CCRCFAIL) || \
((IT) == SDIO_IT_DCRCFAIL) || \
((IT) == SDIO_IT_CTIMEOUT) || \
((IT) == SDIO_IT_DTIMEOUT) || \
((IT) == SDIO_IT_TXUNDERR) || \
((IT) == SDIO_IT_RXOVERR) || \
((IT) == SDIO_IT_CMDREND) || \
((IT) == SDIO_IT_CMDSENT) || \
((IT) == SDIO_IT_DATAEND) || \
((IT) == SDIO_IT_STBITERR) || \
((IT) == SDIO_IT_DBCKEND) || \
((IT) == SDIO_IT_CMDACT) || \
((IT) == SDIO_IT_TXACT) || \
((IT) == SDIO_IT_RXACT) || \
((IT) == SDIO_IT_TXFIFOHE) || \
((IT) == SDIO_IT_RXFIFOHF) || \
((IT) == SDIO_IT_TXFIFOF) || \
((IT) == SDIO_IT_RXFIFOF) || \
((IT) == SDIO_IT_TXFIFOE) || \
((IT) == SDIO_IT_RXFIFOE) || \
((IT) == SDIO_IT_TXDAVL) || \
((IT) == SDIO_IT_RXDAVL) || \
((IT) == SDIO_IT_SDIOIT) || \
((IT) == SDIO_IT_CEATAEND))
#define IS_SDIO_CLEAR_IT(IT) ((((IT) & (uint32_t)0xFF3FF800) == 0x00) && ((IT) != (uint32_t)0x00))
/**
* @}
*/
/** @defgroup SDIO_Read_Wait_Mode
* @{
*/
#define SDIO_ReadWaitMode_DATA2 ((uint32_t)0x00000000)
#define SDIO_ReadWaitMode_CLK ((uint32_t)0x00000001)
#define IS_SDIO_READWAIT_MODE(MODE) (((MODE) == SDIO_ReadWaitMode_CLK) || \
((MODE) == SDIO_ReadWaitMode_DATA2))
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
/* Function used to set the SDIO configuration to the default reset state ****/
void SDIO_DeInit(void);
/* Initialization and Configuration functions *********************************/
void SDIO_Init(SDIO_InitTypeDef* SDIO_InitStruct);
void SDIO_StructInit(SDIO_InitTypeDef* SDIO_InitStruct);
void SDIO_ClockCmd(FunctionalState NewState);
void SDIO_SetPowerState(uint32_t SDIO_PowerState);
uint32_t SDIO_GetPowerState(void);
/* Command path state machine (CPSM) management functions *********************/
void SDIO_SendCommand(SDIO_CmdInitTypeDef *SDIO_CmdInitStruct);
void SDIO_CmdStructInit(SDIO_CmdInitTypeDef* SDIO_CmdInitStruct);
uint8_t SDIO_GetCommandResponse(void);
uint32_t SDIO_GetResponse(uint32_t SDIO_RESP);
/* Data path state machine (DPSM) management functions ************************/
void SDIO_DataConfig(SDIO_DataInitTypeDef* SDIO_DataInitStruct);
void SDIO_DataStructInit(SDIO_DataInitTypeDef* SDIO_DataInitStruct);
uint32_t SDIO_GetDataCounter(void);
uint32_t SDIO_ReadData(void);
void SDIO_WriteData(uint32_t Data);
uint32_t SDIO_GetFIFOCount(void);
/* SDIO IO Cards mode management functions ************************************/
void SDIO_StartSDIOReadWait(FunctionalState NewState);
void SDIO_StopSDIOReadWait(FunctionalState NewState);
void SDIO_SetSDIOReadWaitMode(uint32_t SDIO_ReadWaitMode);
void SDIO_SetSDIOOperation(FunctionalState NewState);
void SDIO_SendSDIOSuspendCmd(FunctionalState NewState);
/* CE-ATA mode management functions *******************************************/
void SDIO_CommandCompletionCmd(FunctionalState NewState);
void SDIO_CEATAITCmd(FunctionalState NewState);
void SDIO_SendCEATACmd(FunctionalState NewState);
/* DMA transfers management functions *****************************************/
void SDIO_DMACmd(FunctionalState NewState);
/* Interrupts and flags management functions **********************************/
void SDIO_ITConfig(uint32_t SDIO_IT, FunctionalState NewState);
FlagStatus SDIO_GetFlagStatus(uint32_t SDIO_FLAG);
void SDIO_ClearFlag(uint32_t SDIO_FLAG);
ITStatus SDIO_GetITStatus(uint32_t SDIO_IT);
void SDIO_ClearITPendingBit(uint32_t SDIO_IT);
#ifdef __cplusplus
}
#endif
#endif /* __STM32F4xx_SDIO_H */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/